Parts Description; Functional Description - Makita AN635H Manual De Instrucciones

3. To maintain product SAFETY and RELIABILITY,
maintenance and repairs should be performed
by Makita Authorized Service Centers, always
using Makita replacement parts.
4. Follow local regulations when disposing of the tool.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.

PARTS DESCRIPTION

► Fig.1: 1. Trigger 2. Trigger lock lever 3. Hook
4. Magazine cap 5. Nose adapter (contact
element)
INSTALLATION
Selecting compressor
140
120
100
80
2
60
40
20
0
0 10 20
1. Nailing frequency (times/min) 2. Compressor air
output per minute (L/min) 3. 2.26 MPa (22.6 bar) 4. 1.76
MPa (17.6 bar) 5. 1.18 MPa (11.8 bar)
The air compressor must comply with the requirements
of EN60335-2-34.
Select a compressor that has ample pressure and air
output to assure cost-efficient operation. The graph
shows the relation between nailing frequency, applica-
ble pressure and compressor air output.
Thus, for example, if nailing takes place at a rate of
approximately 50 times per minute at a compression of
1.76 MPa (17.6 bar), a compressor with an air output
over 100 liters/minute is required.
Pressure regulators must be used to limit air pressure to
the rated pressure of the tool where air supply pressure
exceeds the tool's rated pressure. Failure to do so may
result in serious injury to tool operator or persons in the
vicinity.
3
30 40 50 60
1
Selecting air hose
CAUTION:
or a long or smaller diameter air hose in relation
to the nailing frequency may cause a decrease in
the driving capability of the tool.
► Fig.2
Use a high pressure resistant air hose.
Use an air hose as large and as short as possible to
assure continuous, efficient nailing operation.
Lubrication
► Fig.3: 1. Pneumatic tool oil
Oil the tool with pneumatic tool oil by placing two or
three drops into the air fitting. This should be done
before and after use.
For proper lubrication, the tool must be fired a couple of
times after pneumatic tool oil is introduced.
FUNCTIONAL
DESCRIPTION
CAUTION:
tion on the tool, always lock the trigger by turning
the trigger lock lever to the lock position
disconnect the air hose from the tool.
4
Adjusting depth of nailing
This toll has the adjuster of the nailing depth. To modulate
5
the nailing depth, turn the adjuster to the proper depth.
► Fig.4: 1. Adjuster
The adjustable range is 8.0 mm (5/16"). (One full turn
allows 1.6 mm (1/16") adjustment.)
► Fig.5: 1. Too deep 2. Flush 3. Too shallow
Hook
CAUTION:
hanging the tool using the hook.
CAUTION:
tion or on potentially unstable surface.
CAUTION:
waist belt. If the nailer accidentally drops, it may
result in misfiring and personal injuries.
The hook is useful for hanging up the tool temporarily.
The hook can be turned while pushing the bottom to the
desired angle.
► Fig.6: 1. Hook
Furthermore, this hook can be installed on either side
of the tool.
To change the installation position, unscrew the bolt
with a screwdriver and remove the nut. Install the hook
on another side and then secure it firmly with the bolt
and the nut.
► Fig.7: 1. Hook 2. Bolt 3. Nut
11 ENGLISH
Low air output of the compressor,
Before adjusting or checking func-
Always disconnect the hose when
Never hook the tool at high loca-
Do not hang the hook from the
, and