Noise/Vibration Information; Battery Charging - Bosch GDS 18V-200 Professional Manual Original

14 | English
Cordless impact screwdriver
Max. torque
Machine screw diameter
Tool holder
Weight according to
A)
EPTA-Procedure 01:2014
Recommended ambient temperat-
ure during charging
Permitted ambient temperature dur-
B)
ing operation and during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 95 dB(A); sound power level
106 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2.
Impact tightening of fasteners of the maximum capacity of
the tool:
2
GDR 18V-200: a = 14.0 m/s , K = 1.5 m/s
h
2
GDX 18V-200: a = 10.0 m/s , K = 1.5 m/s
h
2
GDS 18V-200: a = 9.0 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
1 609 92A 53Z | (27.09.2019)
GDR 18V-200
Nm 200
mm M6–M16
¼" internal hexagon
kg 1.1–2.5
°C 0 ...+35
°C –20 ... +50
GBA 18V...
ProCORE18V...
GAX 18...
GAL 18...
GAL 36...
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.

Battery Charging

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
2
Note: The battery is supplied partially charged. To ensure
2
full battery capacity, fully charge the battery in the charger
2
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Observe the notes for disposal.
Removing the battery
The battery (4) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (5)unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (4), press the release button (5) and
pull the battery forward and out of the power tool. Do not
use force to do this.
GDX 18V-200 GDS 18V-200
200
M6–M16
¼" internal hexagon/
∎ ½"
1.1–2.5
0 ... +35
–20 ... +50
GBA 18V...
ProCORE18V... ProCORE18V...
GAX 18...
GAL 18...
GAL 36...
Bosch Power Tools
200
M6–M16
∎ ½"
1.1–2.5
0 ... +35
–20 ... +50
GBA 18V...
GAX 18...
GAL 18...
GAL 36...