Publicidad
Idiomas disponibles
Idiomas disponibles
1. ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make sure that all
of the pieces are there, Fig.1:
(1) Main body; (39) Front trim cover; (41) Top trim
cover; (61) Main post with handlebar and monitor;
(95) Backrest; (124) Flat washer M-10; (117)
Grower washer M-10; (123) Allen screw M-10x25;
(151) Screw M-4x20; (52) Allen screw M-5x15;
(121) Screw M-8x15: (11) Grower washer M-8;
(122)
Flat
washer
spanner; (89) Star driver spanner; (132) Allen key
5mm; (134) Allen key 8mm; (154) Bottle holder;
(X01) The adapter H890TV 15v. 2 Amp.
2.
FITTING THE MAIN POST.-
Take hold of the post (61) and bring it up to the
boss on the main body (1), connect the terminals
(H82; H20; H07; H84; H83), sticking out of the
bottom of the post, with terminal (L06; L04; 26; 25)
coming up out of the top of the tube on the main
body (1), Fig.2, In a similar fashion connect
terminal (R) coming out of the bottom of the focus
bar to terminal (S) coming out of the tube on the
main body (1) Fig.2 now slip the main post over the
boss on the main body in the direction of the arrow,
making sure not to snag any of the cables.
Check that the cables are connected correctly by
spinning the dynamo until the monitor starts to
operate.
Once you have checked that it works, insert
screws (123) along with their flat washers (124)
and Grower washer (117) Fig.2.
Line the main post up with the main body and
tighten the screws securely.
Next, take the backrest (95) and insert it into the
tube on the seat, Fig.2, in the direction of the
arrow.
Fit the screws (121), along with the spring washers
(11) and the flat washers (122).
3.
FITTING THE FRONT TRIM COVER.-
Fit the trim cover (39) by sliding it onto the side
tubes, see Fig.3. Next, take screw (151) and
secure the cover by tightening the screw.
4.
FITTING THE TOP TRIM COVER.-
Position the cover on the side tubes on the main
body (1), in the direction of arrow, Fig.4, sliding the
cover forward in the direction of arrow, Fig.4,
inserting it into the pivots on the main body (1).
Next position it onto the aluminium section and
secure it using screws (52).
Next, remove the screws (155) from the main post
(1), Fig.4A, position the bottle holder and secure it
by using the screws removed previously.
M-8;
(103)
Combination
5.
ADJUSTING THE SEAT.-
The seat can be adjusted by pressing lever (84)
Fig.5, upward, this is on the lower right-hand side
of the seat, and, without releasing it, sliding the
seat backwards or forwards to suit your seating
position.
Once the seat is in a position that suits you,
release the lever (84) and the seat will be locked
into this position.
6.
LEVELLING.-
Once the unit has been placed into its final position
for doing exercise, make sure that it sits flat on the
floor and that it is level. This can be achieved by
screwing the adjustable support blocks (113) up or
down, as shown in Fig.6.
7.
MOVEMENT & STORAGE.-
The appliance is equipped with wheels (119)
making it easier to move about. The two wheels at
the front of the appliance make it easy to store the
machine away, as shown in Fig.7.
8.
PULSE MEASUREMENT.-
Your pulse rate is measured by placing both hands
on pulse sensors (145) located on the seat
handgrips or the handlebar, see Fig.8.
NOTE:
You can also use the chest band (OPTIONAL
TELEMETRIC PULSE SENSOR) to measure your
heart rate.
The reading from the telemetric pulse rate takes
preference over the pulse sensors (145) located on
the seat handgrips or handlebar.
9.
BATTERY CHARGE.-
Before starting the battery charge, make sure that
the mains voltage is compatible with the AC/DC
adaptor.
Connect the AC/DC adaptor (X01) to the mains.
Then, connect the DC terminal to the connector
located at the low end of the chain cover Fig.9.
Do not hesitate to get touch with the Technical
Assistance Service if you have any queries by
phoning customer services (see last page in manual)
BH RESERVES THE RIGHT TO MODIFY
THE SPECIFICATIONS OF ITS PRODUCTS
WITHOUT PRIOR NOTICE.
10
SK
LINE
sportkoncept
Publicidad
