REVELL Control Pulse FPV Manual Del Usuario página 11

• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the transmitter and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
1A Camera lens
1B Status LED
1C Rotors
1D Battery compartment cover
1E Battery compartment
2 TRANSMITTER
2A Control for thrust and rotation. Briefly
press vertically: Headless Mode
2B Control for forward/backwards and
banking. Briefly press vertically: Follow
Me mode
2C Trim for rotation
2D Trim for forwards/backwards
2E Trim for sideways
2F ON/OFF switch
2G Button for photo
3 INSERTING BATTERIES (TRANSMITTER)
3A Cover removal.
3B Insert 4 x 1,5 V AA batteries and pay attention to the polarity,
as shown in the battery compartment.
3C Close the battery compartment cover.
20
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output:
1 x DC 7,4 V / 4,5 Wh
rechargeable
LiPo battery (included)
Capacity: 610 mAh
Battery requirement for the
transmitter:
Power supply:
DC 6 V
Batteries:
4 x 1,5 V "AA"
(not included)
1 MODEL
1F No function
1G Battery connection
1H Micro SD card slot
2H Display
2I Button for video
2J Switch for GPS Hold
2K Switch for Coming Home
2L Power LED
2M No function
2N No function
2O No function
2P Battery compartment cover
2Q No function
4 CHARGING THE FLIGHT BATTERY
Attention: The battery and motor must cool down for 15 to 30 minutes before charging
and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
4A • Remove the battery from the model to charge it
• Insert the USB balancer charger into a mains adapter with USB connection
or an activated USB hub.
• The Status LED on the upper side of the balancer charger will light up.
4B • Now insert the white balancer plug of the battery into the connection on the
the balancer charger.
• The Status LED flashes during the charging process.
• When the Status LED is lit permanently again, the charging process is finished.
The model can fly for up to 10 minutes after a charge time of approx. 150
minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 START PREPARATION
Assembling the rotors:
Remove the protective caps on the rotor shafts and attach the propellers to the shafts
according to the A or B marks.
5A Important: The rotor shafts are flattened on one side. A small bar is visible on the
rotors on the side next to the hub between A/B. Turn the rotor until this marking is
above the flattened side of the rotor shaft.
5B Two different screws are supplied to fasten the rotors:
• Rotors marked with A: black screws, to be turned ANTICLOCKWISE.
Important: left-hand threaded screw!
• Rotors marked with B: silver-coloured screws, to be turned CLOCKWISE.
The circular arrows around the A/B marks on the rotors indicate the direction of
rotation to unscrew the rotor fastening screws.
Important: Always replace a damaged rotor blade. Never fly the quadcopter with
a damaged rotor blade.
5C Removing the camera lens cap
Attention: In order to start the rotors, the following procedure must be followed
step-by-step EACH TIME THE MODEL IS SWITCHED ON.
5D To start the model, first switch on the transmitter, then insert the battery into the
battery compartment of the model.
21