Technical Data; Before Starting The Equipment - EINHELL DTA 25/2 Manual De Instrucciones

Grapadora/clavador de aire comprimido
Ocultar thumbs Ver también para DTA 25/2:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 85

4. Technical data

Max. permitted operating pressure ........... 8.3 bar
Recommended pressure range ................ 6.3 bar
Air consumptioap ........................ prox. 0.66 l/shot
Staple width ............................................. 5.7 mm
Staple length .......................................13 - 40 mm
Nail length ...........................................10 - 50 mm
Recommended hose diameter ..... Diameter 9 mm
Weight............................................ approx. 1,5 kg
Sound and vibration
Sound and vibration values were measured in
accordance with EN 12549, EN ISO 4871.
L
sound pressure level ..................... 83.5 dB(A)
pA
K
uncertainty .......................................... 2.5 dB
pA
L
sound power level ....................... 96.5 dB(A)
WA
K
uncertainty .......................................... 2.5 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Total vibration values (vector sum of three
directions) determined in accordance with
ISO 8662-11-1999, EN 12096.
Vibration emission value ah = 2.5 m/s
K uncertainty = 26.8%
These values for noise emissions are equipment-
based characteristic values and do not refl ect the
noise generated at the place of use. The noise
generated at the place of use will depend, for
example, on the work area, the workpiece, work-
piece support and the number of stapling/nailing
operations.
The value given for vibration is an equipment-
based characteristic value and does not repre-
sent the impact on the hand and arm system
when the equipment is used. The impact on the
hand and arm system when the equipment is
used will depend, for example, on the force of the
grip, the pressing force, the direction in which you
are working, the air pressure setting, the workpie-
ce and the workpiece support.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Anl_DTA_25_2_SPK7.indb 19
Anl_DTA_25_2_SPK7.indb 19
GB
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Compressed air quality:
Purifi ed and with oil mist.
Air supply:
Via a conditioning unit with fi lter pressure reducer
and mist oiler connected to a compressed air
source.
2
Recommended capacity of the compressor:
Compressor with a capacity of approx. 250 l/min,
which is the equivalent of engine power of approx.
2.2 kW
Remember:
Wear the necessary protective clothing when wor-
king with the stapler, in particular safety goggles.
Pay attention to the safety regulations.

5. Before starting the equipment

Each time before starting work, check that the
trigger catch functions perfectly and that all
screws and nuts are securely fastened.
Never tamper with the stapler.
Never dismantle or block any parts of the
stapler such as, e.g. a trigger catch.
Never carry out any "emergency repairs" with
unsuitable means.
Proper stapler maintenance is required at
- 19 -
24.11.2016 13:14:06
24.11.2016 13:14:06

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

41.377.55

Tabla de contenido