Explanation Of General View; Planer Safety Warnings - Makita KP312 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Knob
2 Scale plate
3 Switch trigger
4 Lock button/Lock-off button
5 Restart button
6 Pins
7 Edge fence (Guide rule)
8 Rear base
9 Foot
10 Planer blade
SPECIFICATIONS
Model
Planing width
Planing depth
–1
No load speed (min
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

PLANER SAFETY WARNINGS

1. Wait for the cutter to stop before setting the tool
down. An exposed cutter may engage the surface
leading to possible loss of control and serious injury.
2. Hold the power tool by insulated gripping sur-
faces only, because the cutter may contact its
own cord. Cutting a "live" wire may make exposed
metal parts of the power tool "live" and could give
the operator an electric shock.
4

Explanation of general view

11 Front base
12 Hex wrench
13 Installation bolt
14 Drum plate
15 Set plate screw
16 Set plate
17 Planer blade
18 Adjusting screw
19 Drum
20 Wrench holder
KP312 KP312S
312 mm
0 – 3.5 mm
) 12,000
551 mm
18.4 kg
/II
3. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
4. Rags, cloth, cord, string and the like should
never be left around the work area.
5. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
6. Use only sharp blades. Handle the blades very
carefully.
7. Be sure the blade installation bolts are securely
tightened before operation.
8. Hold the tool firmly with both hands.
9. Keep hands away from rotating parts.
10. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
11. Make sure the blade is not contacting the work-
piece before the switch is turned on.
ENE001-1
12. Wait until the blade attains full speed before cut-
ting.
13. Always switch off and wait for the blades to
ENF002-2
come to a complete stop before any adjusting.
14. Never stick your finger into the chip chute.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
15. Do not leave the tool running. Operate the tool
only when hand-held.
16. Always change both blades or covers on the
GEA010-1
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
17. Use only Makita blades specified in this manual.
18. Always use the correct dust mask/respirator for
the material and application you are working
with.
SAVE THESE INSTRUCTIONS.
WARNING:
GEB010-4
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
21 Chip guide
22 Nozzle assembly
23 Joint
24 At the start of planing
25 At the end of planing
26 Front roller
27 Limit mark
28 Screwdriver
29 Brush holder cap