Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: The original equipment
battery on
your t ractor i s maintenance
free,Donot
attempt toopen orremove caps o rcovers.
Adding orchecking level o f
electrolyte is
not necessary.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and termi-
nals can cause the battery to "leak" power.
1. Remove terminal guard.
2, Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor.
3. Rinsethe batten]with plainwaterand dry.
4. Clean terminals and battery cable ends
with wire brush until bright.
5, Coat terminals with grease or petroleum
jelly.
6. Reinstall battery (See "REPLACING
BATTERY" in the SERVICE AND AD-
JUSTMENTS section of this manual).
........... T RANSAXLE MAINTENANCE
The transmission fan and cooling fins should
be kept clean to assure proper cooling. Do
not attempt to clean fan or transmission while
engine is running or while the transmission
is hot. To prevent possible damage to seals,
do not use high pressure water or steam to
clean transaxle.
• Inspect cooling fan to be sure fan blades
are intact and clean.
• 1nspect cooling fins for dirt, grass clippings
and other materials. To preventdamageto
seals, do not use compressed air or high
pressure sprayer to clean cooling fins.
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory and
fluid maintenance is not required for the life
of the transaxle. Should the transaxle ever
leak or require servicing, contact your near-
est Sears or other qualified service center.
V-BELTS
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, they will result in increased
oil consumption when used above 32°E
Check your engine oil level more frequent-
ly to avoid possible engine damage from
running low on oil.
Change the oil after even] 50 hours of op-
eration or at least once a year if the tractor
is not used for 50 hours in one year.
Check the crankcase oil level before
starting the engine and after each eight
(8) hours of operation. Tighten oil fill cap/
dipstick securely each time you check the
oil level.
TO CHANGE ENGINE OIL
Determine temperature
range expected
before oil change. All oil must meet API
service classification SG-SL.
• Be sure tractor is on level surface.
° 0il will drain more freely when warm.
Catch oil in a suitable container,
1. Remove oil fill cap/dipstick, Be careful
not to allow dirt to enter the engine when
changing oil.
2. Slideoil drain extensionfromthe docking
position on the engine blower housing
and extend outward from engine,
pDo°Ck!ng
Oil Drain
SIIIOB
3. To open, twist cap counter-clockwise
CheckV-belts fordeterioration andwear after
.
,
4
After o I s dra ned completely, replace
-100 Hoursof 0peratiC)n _nd replaceif neces_..................
" ...............................
san). The belts are not adjustable. Replace
cap and twist clockwise until it stops.
belts if they begin to slip from wear.
ENGINE
LUBRICATION
Only use high quality detergentoil rated
with APi service classification SG-SL.
Select the oi!'s SAE viscosity grade
according to your expected operating
temperature,
5. Re-attach oil drain extension to engine
blower housing.
6. Refill enginewith oil through oil fill dipstick
tube. Pour slowly, Do not overfill, For ap-
proximate capacity see "PRODUCT SP-
ECIFICATIONS" section of this manual.
7, Use gauge on oil fill cap/dipstick for
checking level, For accurate reading,
tighten dipstick cap securely onto the
tube before removing dipstick, Keep oil
at "FULL' line on dipstick. Tighten cap
onto the tube securely when finished.
23
Publicidad
Tabla de contenido
