Color Temp - Sony VPL-V500Q Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FILTER
Corrects line patterns that appear on the picture input
from INPUT A.
I N P U T - A
D O T P H A S E : 4 8
INPUT
S I Z E
H : 8 0 0
SELECT
S H I F T H : 1 2 3 V : 1 2 3
PICTURE
CTRL
F I L T E R : O N
C L A M P : A O F F
INPUT
SETTING
C O L O R T E M P : H I G H
SET
S A V E T O M E M O R Y
SETTING
SEL:
SET:
ENTER
RESET: RESET
INPUT
INFO.
EXIT:
MENU
These lines occur when an RGB signal containing
horizontal picture dots other than 640 is input. In such
case, set to ON. The picture will lose some clarity, but
the line patterns will be reduced. Set to OFF to set the
dot number of the input signal to the LCD pixels
number.
CLAMP
Corrects the luminance of the picture input from
INPUT A.
I N P U T - A
D O T P H A S E : 4 8
INPUT
SELECT
S I Z E
H : 8 0 0
S H I F T H : 1 2 3 V : 1 2 3
PICTURE
CTRL
F I L T E R : O F F
C L A M P : A U T O
INPUT
C O L O R
S o n G H B M
SETTING
H / C
SET
SETTING
S A V E T O M E M O R Y
SEL:
SET:
ENTER
RESET: RESET
INPUT
INFO.
EXIT:
MENU
CLAMP is used as a standard for setting the black
level of a picture correctly. The standard position of
the clamp depends on the kind of sync. signal being
used. Normally, the projector CPU judges the signal
and sets the position automatically. However, the CPU
can misjudge the signal because of noise. If the
luminance of the picture seems to be incorrect (too
dark, the black color is too light, or the luminance is
unstable) the clamp position may need to be changed.
AUTO: Automatic setting mode. Normally set to this
position.
SonG: Set to this position if the black seems too
light or greenish.
H/C: Set to this position if the picture is too dark or
luminance is unstable.
Note
If the luminance is still incorrect after changing the
clamp setting, check the input signal and the
connections.

COLOR TEMP

Adjusts the color temperature.
I N P U T - A
D O T P H A S E : 4 8
INPUT
SELECT
S I Z E
H : 8 0 0
S H I F T H : 1 2 3 V : 1 2 3
PICTURE
F I L T E R : O F F
CTRL
C L A M P : A U T O
INPUT
SETTING
C O L O R T E M P : H I G H
L O W
SET
SETTING
S A V E T O M E M H B M
SEL:
SET:
ENTER
RESET: RESET
INPUT
INFO.
EXIT:
MENU
HIGH: Makes the white color bluish.
LOW: Makes the white color reddish.
HBM (high brightness mode): Reproduces a
picture with high brightness.
SAVE TO MEMORY
You can save the settings in the INPUT SETTING
menu in the projector memory. Whenever a new
setting is saved, the previous settings are overwritten.
I N P U T - A
D O T P H A S E : 4 8
INPUT
S I Z E
H : 8 0 0
SELECT
S H I F T H : 1 2 3 V : 1 2 3
PICTURE
CTRL
F I L T E R : O F F
C L A M P : A U T O
INPUT
SETTING
C O L O R T E M P : H B M
SET
S A V E T O M E M O R Y
SETTING
SEL:
SET:
ENTER
RESET: RESET
INPUT
INFO.
EXIT:
MENU
Once you have adjusted the settings, select SAVE TO
MEMORY and press the ENTER or the b key. When
the settings have been saved, the message "Saving is
complete!" appears.
I N P U T - A
D O T P H A S E : 4 8
INPUT
SELECT
S I Z E
H : 8 0 0
S H I F T H : 1 2 3 V : 1 2 3
PICTURE
CTRL
F I L T E R : O F F
C L A M P : A U T O
INPUT
C O L O R T E M P : H B M
SETTING
SET
SETTING
S A V E T O M E M O R Y
SEL:
SET:
ENTER
RESET: RESET
INPUT
INFO.
EXIT:
MENU
S a v i n g i s c o m p l e t e !
Items cannot be adjusted depending on
the types of input signal
Item
Cannot be adjusted with
DOT PHASE
Signal input from VIDEO IN connectors
SIZE
Signal input from VIDEO IN connectors
FILTER
Signal input from VIDEO IN connectors,
component input signal, 15k RGB signal
CLAMP
Signal input from VIDEO IN connectors,
component input signal, 15k RGB signal
SHIFT
Signal input from VIDEO IN connectors
23
(EN)

Publicidad

Capítulos

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Vpl-v500qm

Tabla de contenido