Cleaning And Maintenance - Royal RCPS- 1350 Manual De Instrucciones

Do not turn the package upside down! When transporting
the package, please ensure that it is kept horizontal and
stable. Please keep all packaging materials (cardboard,
plastic tapes and Styrofoam) so that in case of a problem,
the device can be sent back to the service centre as well
-protected as possible.
V. DISPOSAL OF THE PACKAGING
Please keep all packaging materials (cardboard, plastic tapes
and Styrofoam), so that in case of a problem, the device can
be sent back to the service centre in accurate condition!
VI. SAFETY INSTRUCTIONS
1. The popcorn machine should be placed where it
has a strong and stable position (a 3% slant is an
advantage).
2. The device should only be connected with an
appropriate power source.
3. The safety switch / power switch should be located
near the machine. The path must be freely accessible.
4. All electrical connections have to be carried out by
authorized personnel only.
VII. CONSTRUCTION OF THE DEVICE
1. control panel
2. housing
1
3. handle
7
2
4. pot
3
8 5. lid
6. pot connection
9 4
7. light
5
10
6 8. annealed glass
11 9. door
10. lower door
11. draw
FRONT PANEL
1 2
1. STIRRER – turning on the stir function
2. HEAT – turning on the bowl heating
3. WARMING & LIGHT – turning on the interior light
and heating
VIII. OPERATION
1. Set the WARMING&LIGHT (3) switch to ON
position.
2. Set the EAT (2) switch to ON position, add oil, wait
for oil to heat up (3-4 minutes).
8
3. Then set the STIRRER switch to ON position, add
corn kernels (and sugar if required), cover with lid
– wait for all the kernels to pop. Remove from pot
suing the lever by the pot to tip out the popcorn.
4. Please note that during the production of popcorn,
the door needs to be closed so that the hot popcorn
cannot escape and cause burns.
5. You can repeat this procedure as often as you want
to. It only takes approximately 2 minutes until the
corn pops steadily.
6. Do not let any oil drop on the hot plate as it can
result in a fire. WARNING: Do not let any water
drip on the plate during the popcorn popping
procedure.
7. The device is equipped with a thermostat. If the
temperature exceeds the maximum the machine
switches off automatically to ensure the required
safety.
ATTENTION: The pot has to be emptied and the heating
turned off as soon as the frequency (approx. 2-3 seconds)
of popping slows down. Only like this, burning of sugar
and popcorn as well as damage to the coating can be
prevented. It is not always possible for all corn to pop.
Remove residues after every production cycle. We cannot
assume liability for damages to the pot's coating due to
improper use.
IX. CLEANING AND MAINTENANCE
1. Switch off the device and disconnect the power plug
in order to prevent accidents when cleaning the
machine.
2. To clean the device from the outside, use a wet cloth
with some corrosion protection. DO NOT clean the
machine with water as it can damage the electric
function of the device.
3. If the device is not used for a prolonged period of
time, unplug the power plug.
4. DO NOT clean the inside of the device with hard
3
metallic objects, as this will damage the coating of
the machine.
X. TRANSPORT UND LAGERUNG
During transport, the machine should be protected
from shaking, falling and turning upside down. Store it in
a properly ventilated place with dry air and without any
corrosive gas.
Rev. 26.06.2017
XI. CHECK REGULARLY THE DEVICE
Regularly check the machine for signs of damage. If the
machine is damaged, please stop using it immediately and
contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare the
following information:
• Invoice number and serial number (the latter is to
be found on the technical plate on the device).
• If relevant, take a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk to
determine the source of the problem if you give
a detailed and precise description of the matter.
The more detailed your information, the better
customer service will be able to solve your problem
rapidly and efficiently!
CAUTION: Never open the device without the
authorization of your customer service. This can lead to
a loss of warranty!
Manufacturer
expondo Polska sp. z o.o. sp. k.
ul. Dekoracyjna 3, 65-155 Zielona Góra | Poland, EU
Product name Popcorn Maker
Model RCPS-1350
Power
Voltage 230V~
Frequency 50Hz
Weight 17kg
Serial-No.
Production year
Design Made In Germany
expondo.de
Rev. 26.06.2017 9