Custom Code Setting; Switching The Upper Limit Of Cooling Temperature; Dip Switch Setting; Function Setting - Fujitsu Airstage ARXC72GATH Manual De Instalación

7.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up.
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Confusion
Indoor
unit
Remote
controller
Custom code setting for indoor unit
Set the DIP switch SET 3 SW1, SW2 referring to the Table B.
ON
OFF
SW SW SW
1 2 3
Table B
A (Factory setting)
DIP switch SET3 SW1
DIP switch SET3 SW2

7.3. Switching the upper limit of cooling temperature

This setting can be raised the upper limit of the cooling temperature setting range.
This setting can be used when connecting to the following controllers.
• Wired remote controller (2-wire type)
• Central remote controller
• Touch panel controller
• System controller
• Service tool
• Web monitoring tool

DIP switch setting

Set the DIP switch SET 4 SW3 referring to the Table C.
ON
OFF
SW SW SW SW
1
DIP switch SET 4 SW3
OFF (Factory setting)
ON
NOTE :
Please do not make a standard setup and an extension setup intermingled in remote
controller group.
1
9365748145-01_IM.indb Sec1:14 9365748145-01_IM.indb Sec1:14
Code change
A B C D
A B C D
Dip switch "SET 3"
SW
4
Custom code
B C
OFF ON OFF
OFF OFF ON
DIP switch "SET4"
2 3 4
Table C
Cooling temperature setting range
Standard (18 to 30 °C)
Extension (18 to 32 °C)

7.4. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
(Set IU AD, REF AD SW to 0)
• Refer to "7.1. Setting the address" for indoor unit address and refrigerant circuit address
settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
tight test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
Function details
Function
Function Setting number
number
00
Filter indica-
11
01
tor interval
02
00
01
Filter indica-
13
tor action
Display only on
02 central remote
00
Cool air
temperature 30
01
trigger
02
00
Heat air
01
D temperature 31
trigger 02
ON
ON
03
00
Auto restart 40
01
00
Cool Air
43
Prevention
01
00
01
External
46
control
02
00
Error report
47 Display only on
target
01 central remote
Fan set-
ting when 00
cooling 49
thermostat
OFF
01
Default Details
○
Default
Adjust the fi lter cleaning interval notifi ca-
tion. If the notifi cation is too early, change
Longer
to setting 01. If the notifi cation is too late,
change to setting 02.
Shorter
○
Enable
Enable or disable the fi lter indicator.
Disable
Setting 02 is for use with a central remote
controller.
controller
○
Default
Adjust the cool air trigger temperature. To
lower the trigger temperature, use setting
Adjust (1)
01. To raise the trigger temperature, use
setting 02.
Adjust (2)
○
Default
Adjust the heat air trigger temperature.
To lower the trigger temperature by 6
Adjust (1)
degrees C, use setting 01. To lower the
trigger temperature by 4 degrees C, use
Adjust (2)
setting 02. To raise the trigger tempera-
ture, use setting 03.
Adjust (3)
Enable
Enable or disable automatic system
○
restart after a power outage.
Disable
○
Super low
Restrain the cold airfl ow with making
the airfl ow lower when starting
Follow the
heating operation. To correspond to
setting on
the ventilation, set to 01.
the remote
controller
○ Allow an external controller to start
Start/Stop
or stop the system, or to perform an
emergency stop.
Emergency
* If an emergency stop is performed from
stop
an external controller, all refrigerant
systems will be disabled.
* If forced stop is set, indoor unit stops by
Forced stop
the input to the external input terminals,
and Start/Stop by a remote controller is
restricted.
○
All
Change the target for reporting errors. Er-
rors can either be reported in all locations,
or only on the wired remote.
controller
Follow the When set to 01, the fan stops when
setting on ○ the thermostat is OFF in cooling
the remote operation. Connection of the wired re-
controller mote controller (2-wire type or 3-wire
type) and switching its thermistor are
Stop
necessary.
En-14
7/12/2012 11:09:17 AM 7/12/2012 11:09:17 AM