Festool RENOFIX RG 130 E Manual De Instrucciones Original página 13

b) Never place your hand near the rotating ac-
cessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite to
the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre-
quent kickback and loss of control.
Additional safety instructions for grinding and
cutting
Safety Warnings Specifi c for Grinding and
ABRASIV Cutting-Off Operations:
a) Use only wheel types that are recommended
for your power tool and the specifi c guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The guard must be securely attached to the
power tool and positioned for maximum safe-
ty, so the least amount of wheel is exposed
towards the operator. The guard helps to pro-
tect operator from broken wheel fragments
and accidental contact with wheel.
c) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. ABRASIV cut-off
wheels are intended for peripheral grinding,
side forces applied to these wheels may cause
them to shatter.
d) Always use undamaged wheel fl anges that
are of correct size and shape for your selected
wheel. Proper wheel fl anges support the wheel
thus reducing the possibility of wheel break-
age. Flanges for cut-off wheels may be differ-
ent from grinding wheel fl anges.
e) Do not use worn down wheels from larger
power tools. Wheel intended for larger power
tool is not suitable for the higher speed of a
smaller tool and may burst.
Additional safety instructions for wire brushing
operations
Safety Warnings Specifi c for Wire Brushing
Operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive
load to the brush. The wire bristles can easily
penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work
load and centrifugal forces.
Further safety instructions
- The machine may not be used in damp and wet
spaces, outdoor when it is rainy, foggy or snowy
or in the explosive environment.
- Before use always inspect the fl exible lead and
the plug. Have the defects repaired by a spe-
cialist repair shop.
- Outside the premise use only approved exten-
sion leads and cable connections.
- Apply the machine to the material only when
switched on.
- Do not carry the machine by the lead.
- Do not work on a ladder.
- When operating the tool, use protective gloves
and tough footwear.
- When operating the tool, use goggles and ear
protectors.
- The dust generated during work is harmful to
health. When operating the tool, use the dust
extraction system and the respirator.
- Materials containing asbestos can only be pro-
cessed by qualifi ed individuals. Comply with the
safety regulations that apply in your country.
- Flexible power supply cable always route from
the tool backwards.
- Use only grinding wheel recommended by the
manufacturer.
- The machine can only be used with attached
protective cover and attached front handle.
- Insert the fl exible supply plug into the socket
only if the machine is off.
- Make yourself sure whether the material that is
going to be machined does not contain electric,
water or gas lines – an injury could occur.
- Do not grind metal surfaces, nails or screws.
- The machine is not allowed to be operated by a
person under 16 years of age.
- Only for AS/NZS: The tool shall always be sup-
plied via residual current device with a rated re-
sidual current of 30 mA or less.
13