Virutex MEB250A Manual De Instrucciones página 6

E N G L I S H
MEB250A TABLE FOR EDGEBANDER
1. SAFETY INSTRUCTIONS FOR USING THE
TABLE MEB250A FOR THE PEB200/PEB250
PORTABLE HOT GLUE EDGEBANDERS
Before using the MEB250A, read the ma-
nual for the PEB200/PEB250 edgeban-
ders and ensure you have understood it.
Then read these OPERATING INSTRUC-
TIONS and the attached GENERAL
SAFETY INSTRUCTIONS LEAFLET care-
fully before using the machine.
Keep manuals within easy reach for
possible consultation later on.
Fix the MEB250A to the workbench
through the holes (K, Fig. 1) in the legs.
2. SPECIFICATIONS
Base measurements......................................860 x 350 mm
Working surface length..........................................800 mm
Working surface height...........................................195 mm
Maximum board thickness (0.5 - 2 mm).....45 mm (1- 3/4")
Maximum board thickness (3 mm tape).......25 mm (1")
Weight..........................................................................17 kg
3. STANDARD EQUIPMENT (Fig. 1)
- Auxiliary pressure roller (P).
- Support guides for inserting and removing the
piece (M) (L).
- Rear support guide which can be extended up to
500 mm (A).
- Removable clamp on rear support guide (F).
• You will find the following items inside the box
of the MEB250A:
• 1 MEB250A table for PEB200/PEB250 edgebander.
• 1 Rear, extendible support guide, disassembled into
the following parts:
1 rear support bar (A, Fig. 1)
2 washers (B, Fig. 1)
2 M.8x35 allen screws (C, Fig. 1)
2 arm supports (D, Fig. 1)
2 arms (E, Fig. 1)
1 presser unit (F, Fig. 1)
•1 Bag containing 3 screws (J, Fig. 5) for assembling
6
the PEB200/PEB250; 2 machine attachments (T and
U, Fig. 5) and 18 worktop attachments (S, Fig. 5), for
edgebanding round pieces; and 5 rear attachments
(V, Fig. 5) for edgebanding curved shapes
• 1 Roll-holder (disassembled), consisting of:
1 loader Set (IN, Fig. 3)
1 support set (IL, Fig. 3)
2 tri-lobe screws M5x20 Torx. (IM, Fig. 3)
4. OPTIONAL ACCESSORIES
Machine prepared for the assembly of a portable
feeder, with an independent connection (IW, Fig. 2).
5. FITTING
5.1 FITTING THE REAR GUIDE PLATE
Insert an arm (E, Fig. 1) in each of the two guides (G,
Fig. 1) attached to the sides of the table.
Remove the screws (C, Fig. 1) and the washers (B,
Fig. 1) from the arms (E, Fig. 1).
Mount the rear support bar (A, Fig. 1) on the arms E,
and fix it to the supports (D, Fig. 1) using the screws
(C, Fig. 1) and the washers (B, Fig. 1).
Move the rear guide plate into the guides (G, Fig.
1) until it touches the bar (H, Fig. 1) of the table.
Fix the rear support guide in this position with the
levers (I, Fig. 1) on both sides.
Loosen the screws (C, Fig. 1); make the surfaces of
the rear support bar (A, Fig. 1) flush with the bar (H,
Fig. 1) on the table and tighten the screws (C, Fig.
1) in this position.
5.2 ASSEMBLY OF THE LOADER AND ROLL
Fix the support (IL, Fig. 3) onto the frame of the
MEB250A, using the screws provided (IM, Fig. 3) and
connect the loader (IN Fig. 3).
Place the roll (IO, Fig. 4) of edging onto the loader
(IN Fig. 3,4).
Align the edge (IP, Fig. 4) on the support square
(IQ, Fig. 4).
5.3 FITTING EDGEBANDER PEB200/PEB250
TO THE TABLE
Place the edgebander PEB200 or PEB250 on the table
MEB250A in the position shown in (Fig. 2) and fasten
it with the three screws (J, Fig 2).
5.4 FITTING EDGEBANDER PEB50/PEB150
TO THE TABLE
Remove the spring (2A, Fig. 6.1). Remove the screws
(2C, Fig. 6.1) and the protector (2B, Fig. 6.1).