Care & Cleaning - JENN-AIR w10169649 Guia De Usos Y Cuidados

Horno mural a gas
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

C
& C
ARE
Self-Clean Oven
CAUTION
• It is normal for parts of the oven to become hot during a
self-clean cycle.
• To prevent damage to oven door, do not attempt to open
the door when LOCK is displayed.
• Avoid touching door, window or oven vent area during a
clean cycle.
• Do not use commercial oven cleaners on the oven finish
or around any part of the oven. They will damage the
finish or parts.
The self-clean cycle uses above-normal cooking temperatures to
automatically clean the oven interior.
It is normal for flare-ups, smoking, or flaming to occur during
cleaning if the oven is heavily soiled. It is better to clean the oven
regularly rather than to wait until there is a heavy build-up of soil
in the oven.
During the cleaning process, the kitchen should be well venti-
lated to get rid of normal odors associated with cleaning.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The oven light may
burn out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the oven.
The oven racks will discolor and may not slide easily after a
self-clean cycle if they are not removed.
3. Clean oven frame, door frame, area outside of gasket, and
around the opening in the door gasket with a nonabrasive
cleaner such as Bon Ami* or detergent and water. The self-
cleaning process does not clean these areas. They should be
cleaned to prevent soil from baking on during the clean cycle.
(The gasket is the seal around the oven door and window.)
4. To prevent damage, do not clean or
rub the gasket around the oven door.
The gasket is designed to seal in heat
during the clean cycle.
5. Wipe up excess grease or spillovers
from the oven bottom. This prevents
excessive smoking, flare-ups or flam-
ing during the clean cycle.
6. Wipe up sugary and acidic spillovers such as sweet potatoes,
tomato, or milk-based sauces. Porcelain enamel is acid-
resistant, not acid-proof. The porcelain finish may discolor if
acidic or sugary spills are not wiped up before a self-clean
cycle.
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
LEANING
To set Self-Clean:
Note: Oven temperature must be below 400° F to program
a clean cycle.
1. Close the oven door.
2. Press the Clean pad.
• CLEAN and SET flash in the display.
3. Press the Autoset 0 pad.
• MEd (Medium Soil, 3 hours) is displayed.
4. Press the Autoset 0 pad to scroll through the self-cleaning
settings.
HVy (Heavy Soil, 4 hours)
MEd (Medium soil, 3 hours)
LITE ( Light Soil, 2 hours)
Choosing the soil level of the oven automatically programs
the self-cleaning time.
5. After four seconds, the oven will start cleaning.
• If the door is not closed, beeps will sound and "door" will
display. If the door is not closed within 30 seconds, the
self-cleaning operation will be canceled and the display
will return to the time of day.
• CLEAN will appear in the display.
• LOCK will flash in the display. Once the door locks, the
word will remain steady.
• The cleaning time will start counting down in the display.
To Delay a Self-Clean Cycle:
1. Press the Delay 1 pad.
• DELAY and 00:00 will flash in the display.
2. Enter the amount of time you want to delay the
cycle using the appropriate number pads.
3. Press the Clean pad.
• SET flashes in the display.
4. Press the Autoset 0 pad.
• LITE (Light soil level) is displayed.
12
cont.

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido