JB Systems Light LED MANAGER Manual De Instrucciones página 5

ENGLISH
• Blue wire: This the power for the blue LEDs (max. 50W)
Just connect these 4 wires to the corresponding 4 wires of the projector. (in most cases the colors of
the wires match with the LED colors) Make sure not to exceed the maximum allowed load!
Example: you can connect up to 50 "GROUND LIGHT" on each output cable (total = 100pcs!)
Electrical installation in Master/slave-mode:
• You need to "daisy chain" the DMX in/outputs of 2 or more units with a good quality balanced cable (ex.
JB Systems ref. 7-0063).
• The unit with a free DMX-input connector automatically becomes the master (master LED is lit), the other
units are automatically switched as slaves (slave LED is lit). The controls on the slave units are disabled.
Electrical installation in Master/slave-mode with the LEDCON-01 remote:
• You need to "daisy chain" the DMX in/outputs of 1 or more units with the output of the LEDCON-01
remote using a good quality balanced cable (ex. JB Systems ref. 7-0063).
• The LEDCON-01 remote will be used to control all connected slaves. The LED Managers are
automatically switched as slaves (slave LED is lit). The controls on the slave units are disabled.
Electrical installation in DMX-mode:
• The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
"daisy chain" your DMX controller and all the connected units with a good quality balanced cable (ex. JB
Systems ref. 7-0063).
• To prevent strange behavior of the light effects, due to interferences, you must use
a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this
simply won't work!
• Each unit in the chain needs its proper start address so it knows which commands
from the DMX-controller it has to decode. When you need a lot of power you can
use several LED managers and give them the same start address. In the next chapter you will learn how
to set the DMX addresses.
JB SYSTEMS®
OPERATION MANUAL
5/46 LED MANAGER
ENGLISH
Changing the internal batteries:
VERY IMPORTANT: ONLY rechargeable batteries are allowed, do NOT use normal batteries!!!
The LED Manager has an internal real-time 24H clock with 3 individual timers and battery backup. To use
the battery backup feature you must install 3 optional AA-type NiMH rechargeable batteries. Once these
batteries are installed they will be recharged automatically, no need to replace them anymore!
• Switch the unit off and disconnect the mains cable.
• Use an appropriate screwdriver to unscrew the 10
screws of the enclosure.
• Gently remove the top cover (careful for the cables
inside!)
• On the inside you will find a battery compartment,
next to the fan. Open it gently and install the 3 AA-
type NiMH rechargeable batteries as indicated.
• Close the battery compartment
• Put the top cover back in place and fasten the 10
screws.
• Connect the unit to the mains: the batteries will
charge automatically.
• Done!
SETUP MENUS + DMX ADDRESSING
During normal operation the display shows the current
time of the internal 24H clock.
• Press the MENU button to enter menu mode:
• With the UP and DOWN buttons you can browse
through the different options of the main menu.
• Press the ENTER button to select and edit a menu
option.
• Adapt the values with the UP & DOWN buttons and
confirm with the ENTER button or press the MENU
button again if you want to return to the main menu
without saving the changes you just made.
• After some time the display will automatically show
the internal clock. You can also switch to the clock
display by pressing the MENU button for about 1
second.
DMX start address setting
Used to set the start address of the LED Manager.
• Press the MENU button and UP/DOWN buttons until
the display shows "Addr"
• Press the ENTER button: the display starts blinking.
• Use the DOWN and UP buttons to change the DMX
address.
• Once the correct address is shown on the display, press the ENTER button to save it.
Remarks: You can abort the setting procedure and go back without saving the changes by shortly pressing
the MENU button. When the setup is done and changes are saved, you can return to the clock display by
pressing the MENU button for more than 1second.
Internal 24H clock setting
Used to set the time of the internal 24H clock.
• Press the MENU button and UP/DOWN buttons until the display shows "time"
• Press the ENTER button, the HOUR-display starts blinking.
• Use the DOWN and UP buttons to set the correct hours (00 to 23).
• Press the ENTER button, the MINUTE-display starts blinking.
• Use the DOWN and UP buttons to set the correct minutes (00 to 59).
JB SYSTEMS®
OPERATION MANUAL
6/46 LED MANAGER