Makita PJ7000 Manual De Instrucciones página 6

ENGLISH
(Original instructions)
1 Pointer
2 Stopper
3 Adjusting screw
4 Rubber spike
5 Lock lever
6 Angle guide
7 Knob
8 Scale
9 Tighten
10 Loosen
SPECIFICATIONS
Model
Type of blade ................................................. Plate joiner
Max. grooving depth
Plate joiner blade................................................ 20 mm
–1
No load speed (min ) .......................................... 11,000
Overall length ..................................................... 302 mm
Net weight ............................................................. 2.5 kg
Safety class ..............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting crescent shaped slots for
the placement of flat wooden dowels or biscuit by a
plunging action.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
PLATE JOINER SAFETY WARNINGS
1. Blades must be rated for at least the speed
marked on the tool. Blades running over rated
speed can fly apart and cause injury.
2. Always use the guard. The guard protects the
operator from broken blade fragments and uninten-
tional contact with the blade.
6
Explanation of general view
11 Down
12 Up
13 Center of blade thickness
14 Fence
15 Angle scale
16 Blade cover
17 Set plate
18 Thickness of set plate
19 Lock nut
20 Plate joiner blade
3.
PJ7000
4.
5.
/II
6.
7.
8.
ENE013-1
9.
10. Always place the workpieces on a stable work-
11. Secure the workpieces firmly with clamp or vise.
12. NEVER wear gloves during operation.
ENF002-2
13. Hold the tool firmly with both hands.
14. Keep your hands and body away from the groov-
15. Run the tool for a while without the blade point-
16. Never reach your hands underneath the work-
GEA010-1
17. Do not leave the tool running unattended.
18. Always be sure that the tool is switched off and
19. Some material contains chemicals which may be
GEB020-4
20. Do not use blunt or damaged blades.
21. Do not use the tool with damaged guards.
SAVE THESE INSTRUCTIONS.
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
21 Inner flange
22 Clamp screw
23 Shaft lock
24 Dust bag
25 Fastener
26 Dust nozzle
27 Exhaust vent
28 Inhalation vent
29 Slide switch
Hold power tool by insulated gripping surfaces,
because the blade may contact its own cord. Cut-
ting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
Use only the blades specified for this tool.
Never operate the tool with the blade locked in
exposed position or without the blade cover
secured properly in place.
Make sure that the blade slides smoothly before
operation.
Check the blades carefully for cracks or damage
before operation. Replace cracked or damaged
blades immediately.
Make sure that the flange fits in the arbor hole
when installing the blade.
Inspect for and remove all nails or foreign matter
from the workpieces before operation.
bench.
ing area.
ing toward anybody. Watch for vibration or wob-
bling that could indicate poor installation or a
poorly balanced blade.
pieces while the blade is rotating.
unplugged before making any adjustments or
replacing the blade.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
WARNING: