Publicidad
ENG
Instruction Manual OTOS PL/E27
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
230454
230455
Operating voltage:
230V ~50Hz
Safety class:
Safety type:
IP 43
Bulb:
TC-D, G24d-2, 18W
Dimensions (cm):
Ø/H: 17/110,5
Weight (kg):
2,65 kg
Importer:
SLV Elektronik GmbH
IP 43: Protection against foreign objects > Ø 1,0mm - Protection against
spraying water up to 60° to the vertical.
3.
Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for installation on the ground.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
Separate Installation Steps
Prepare the power supply line according to the rules for electric outdoor
installations.
You may fix the fitting on the ground by applying the anchors or using
regular dowels and screws.
Using the anchors (fig. a)
Prepare a concrete foundation.
Equip the drilling template with the anchors and the nuts. Screw the
nuts completely on the thread.
Press the anchors into the fresh concrete, until the template lies
evenly on the surface. Remove the template after the concrete
hardened.
Unscrew the headless screws on the lamphead. Remove the lamphead
(1).
Direct the mains lead through the tube (2).
Fasten the fixture on the installation surface (3). Ensure a secure
attachment.
Electrical Connection (4)
The product must be able to be separated by an all pole separation from
the current supply.
Direct the mains lead through the strain relief.
For electric connection attach the black or brown wire (live conductor) of
the mains power supply with the black or brown wire of the fixture and
the blue wire (neutral conductor) of the mains power supply with blue
wire of the fixture. The green-yellow wire (protective conductor) of the
mains supply has to be tightly screwed into the earth clamp
product.
Secure the strain relief.
Attach the lamp head.
Unscrew the headless screws of the top cover to remove it (5).
Inserting the bulb: Touch energy-saving-lamps on the plastic housing,
not on the bulb glass. TC-D: Stick the bulb into the socket. E27: Screw
the bulb into the socket.
Put the cover back on.
The product is now ready for operation.
230464
230465
I
Energy-saving lamp,
E27, max. 15W, max.
15 cm long
Ø/H: 15,5/93,5
2,60 kg
.
Use only
4.
Operation
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
a
5
5
1
1
N
L
4
4
2
3
:
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
of the
thawing salt
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface. Cleaning tip: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
08/2006 by SLV Elektronik GmbH
230454/55/64/65
Technical Details are subject to change.
F
Mode d'emploi
1.
A utiliser comme indiqué :
Ce produit ne sert qu'à éclairer:
il est prévu pour une tension de 230V ~50Hz.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu'après examen si le produit a été stocké dans un
entrepôt humide ou sale.
il ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2.
Informations techniques:
230454
Tension
d'alimentation:
Classe de protection:
Degré de protection:
Ampoule:
TC-D, G24d-2, 18W
Dimensions (cm):
Ø/H: 17/110,5
Poids (kg):
Importateur:
IP 43: Protection contre les corps étrangers durs > 1,0 mm - Protection
contre l'eau vaporisée venant de la verticale jusqu'à 60°.
3.
Installation
La connection électrique doit être exécutée par un professionnel,
lequel est familier des normes en vigueur!
Attention: Mettez l'alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l'installation ainsi que le
produit ne peuvent pas être garantis.
high salt content in the air
cleaning agents
Duplication prohibited !
OTOS PL/E27
230455
230464
230465
230V ~50Hz
I
IP 43
Lampe ´economie
d'énergie, E27, max.
15W, long. max.15 cm
Ø/H: 15,5/93,5
2,65 kg
2,60 kg
SLV Elektronik GmbH
Publicidad
