Advanced Configuration; Built-In Timer; Maintenance - Espa Evopool SilenPlus Manual De Instrucciones

6.3 Filter saturation warning.
When the system detects that it has reached its satu-
ration level, the pump will request that a filter cleaning
cycle be run.
- The LED will blink quickly.
- If you have the
ceive the corresponding warning when the pump is
connected.
After cleaning the filter, the warnings will disappear
and the system will return to its normal status.
6.3 Deactivation.
To deactivate
- Press "M" for 5 seconds.
- The " " LED will blink 3 times.
The function will be deactivated and the
LED will stop blinking.
6.4 System control.
You can activate and deactivate
control the system status through the
application.

7. ADVANCED CONFIGURATION

Different speeds can be set to adjust the functions to
the characteristics of the installation.
The function being run will be configured.
To configure a function, first select it, either in Manual
or Remote mode, and at the same time press M + F
for 5 seconds.
All the speeds of the selected function will return to
the factory settings [= fs]
To increase or decrease the speed, press M or F:
M = + 58 RPM (+ 1 Hz)
F = - 58 RPM (- 1 Hz)
Configuring
The filtration speed is set.
· Minimum = 1,600 RPM (20 Hz), [= fs]
· Maximum = 2,900 RPM (50 Hz), [= fs]
Configuring
The maximum and minimum speeds are set, al-
ways maintaining a differential of 20 Hz between
them
· Minimum = 1,600/2,320 RPM (20/40 Hz), [= fs]
· Maximum = 1,740/2,900 RPM (30/50 Hz)
Configuring the Mixed Cycle (Manual only)
The factory setting is 2,320 RPM (40 Hz)
· Minimum = 1,600 RPM (20 Hz)
· Maximum = 2,900 RPM (50 Hz), [= fs]
If M and F are not pressed for 5 seconds the new val-
ues are stored and the configuration mode is
deactivated.
can also be entirely configured using
the application.
application, you will re-
and
.
.

8. BUILT-IN TIMER

The pump has an internal clock that can
operate as a start and stop timer, making external
programming unnecessary.
With this function,
pendently.
ATTENTION: the programming and mainte-
nance of the timer is only possible through the
app.
8.1 Activating the timer.
DANGER. Electrocution risk.
Never open the
the power supply off at least 5 minutes before-
hand.
Lift the cover by loosening the 4 screws.
(See figure 5)
Activate the Timer using the mini-switch, moving it
to the "ON" position.
Replace the cover and fix it with the 4 screws.
Torque: 0.5 Nm.
8.2. Time setting.
Link with the external device using Bluetooth,
following the instructions on the device.
Run the app and follow its indications.

9. MAINTENANCE

:
If is not communicating with
may be necessary to replace the battery.
Proceed as in section 4.2.
It is a 1.5 V, CR2450 type battery.
:
Our equipment is maintenance free.
Clean the equipment with a damp cloth and without
using aggressive products.
In freezing weather, take the precaution of emp-
tying the pipes.
If the equipment is going to be inactive for a
long time, you are recommended to dismantle it
and keep it in a dry, well-ventilated place.
WARNING: in case of a breakdown, the equip-
ment must only be touched by an authorised
service technician.
The list of official technical services can be found at
www.espa.com.
When the time comes to throw the product away, it
does not contain any toxic or polluting material. The
main components are duly identified so you can dis-
pose of them selectively.
12
EN
can operate entirely inde-
cover without turning
it