Maintenance Interval; Optional Accessories - Dolmar HT-CS 3 Manual De Instrucciones

Lubricating moving parts
NOTICE:
Follow the instruction of the frequency and amount
of grease supplied. Otherwise insufficient lubrication may damage
moving parts.
► Fig.12
Gear case:
CAUTION:
Do not apply grease when the gear case is hot.
Hot gear case can cause burn injury.
Apply grease every 25 working hours.
1. The grease hole locates under the bolt. Remove the bolt to
lubricate.
2. Add approx. 3 g (4 cc) of lubricant to the point A of the gearbox
and 5 g (7 cc) of the lubricant to the point B respectively via the
grease hole.
3.
Return the bolt after lubrication.
► Fig.13: 1. Grease hole
NOTE: After filling correct amount of grease, grease will come out a
bit from the base of the blade during the first operation.

MAINTENANCE INTERVAL

-
Whole unit Visually inspect for dam-
All fixing screws and nuts
Blades Inspect for damage, crack
Adjust the clearance
Gear case
Drive axle
Power unit
TROUBLE SHOOTING
State of abnormality
The motor does not start.
The motor stops soon after its start.
The maximum speed is limited.
The blades do not move.
Stop the motor immediately!
The blades do not move.
Stop the motor immediately!
The blades do not move.
Stop the motor immediately!
The unit vibrates abnormally.
Stop the motor immediately!
The blades do not stop.
Stop the motor immediately!

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments are recom-
mended for use with your Dolmar tool specified in this manual.
The use of any other accessories or attachments might present a
risk of injury to persons. Only use accessory or attachment for its
stated purpose.
If you need any assistance for more details regarding these accesso-
ries, ask your local Dolmar Service Center.
• Blade set
• Grease set
Before operation
aged parts
Tighten
and dull edge
Supply grease
Supply grease
Probable cause (malfunction)
Refer to the instruction manual of the power unit.
Refer to the instruction manual of the power unit.
Refer to the instruction manual of the power unit.
Inappropriate angle of cutter unit.
A twig is caught by the blades.
The drive system does not work properly.
The drive system does not work properly.
The power unit does not work properly.
Drive axle:
Apply grease every 25 working hours.
► Fig.14
Overall inspection
• Tighten loose bolts, nuts and screws.
• Check for damaged parts and blades. Ask our authorized service
center to replace them if necessary.
Storage
WARNING:
chapter "IMPORTANT SAFETY INSTRUCTIONS" and the
instruction manual of the power unit.
When storing the attachment, always remove it from the power unit.
1. Turn the lock lever to the direction in the figure and pull out the
attachment while pressing the release button.
► Fig.15: 1. Lock lever 2. Release button 3. Attachment
2. Attach the blade cover. Hold the cutter unit handle and fold the
blade as shown while pulling the angle lock.
► Fig.16: 1. Angle lock 2. Cutter unit handle
3. Attach the cap onto the end of the shaft.
► Fig.17
Daily (10h)
-
-
-
- -
- -
- -
Refer to the instruction manual of the power unit
Remedy
Refer to the instruction manual of the power unit.
Refer to the instruction manual of the power unit.
Refer to the instruction manual of the power unit.
Make sure the angle lock engages properly.
Remove the foreign matter.
Ask our authorized service center to inspect and repair it.
Ask our authorized service center to inspect and repair it.
Refer to the instruction manual of the power unit.
NOTE: Some items in the list may be included in the tool package
as standard accessories. They may differ from country to country.
8 ENGLISH
Follow the warnings and precautions in the
25 h
-
-
-
-
If required
-
-
-
-
-