Hoover H-PURE 700 STEAM Manual De Instrucciones página 5

Low Steam Intensity: Use on delicate floors such as sealed wooden floors and laminate
floors and on rugs or carpet.
Medium Steam Intensity: Use on tiles and vinyl floors.
High Steam Intensity: Use on marble and stone floors and to remove any stubborn dirt.
NOTE: These recommendations should be respected in order to avoid damage to
floors. We recommend that you check the user guide and any warnings from the
floor manufacturers. Test steam mop in a small area before mopping a larger one.
3. Press the floor type selector pedal to select Hard Floors or Standard Carpet and
Rugs. [7]
4. Recline to unlock the cleaner by placing a foot on the nozzle and lowering the main
body to use. [11]
5. To start steaming, press the steam trigger on the handle. [14]
6. Release the steam trigger button on handle to stop the steam function.
VACUUM & STEAM MODE
The combination of steam and vacuum mode allows a perfect and hygienic cleaning in
one–go.
Follow the steps described in the section STEAM MODE and switch the VACUUM button
onto the handle to activate the suction.
USING THE PORTABLE STEAM HANDHELD
The portable steam handheld can be used to hygienize different surfaces: kitchen work
surfaces, oven grills, bathrooms, taps, grouting, windows and mirrors, upholstery (sofas,
armchairs, mattresses, cushions, car interiors), and to refresh clothes and curtains.
You can choose from a variety of accessories depending on what tasks you are
performing.
1. Release the portable steam handheld by pressing the Push & Go and lift upwards
the handheld unit button on product main body. [15]
2. Fill the water tank by releasing it through the tank release button, open the lid and fill in
tap water. Close the lid and put the water tank back on the cleaner. [4,5] This operation
must always be carried out with the power cable disconnected from the mains and the
cleaner has fully cooled down.
3. Fit the Refresh Conical Pipe accessory or the Steam Hose to the steam outlet. [16]
Rotate the conical pipe or the steam hose clockwise aligning the graphic marks until
securely locked in position.
4. Plug the cleaner into the mains power and press the main on/off button on the steam
handheld. [6] After a few seconds the steam ready light (BLUE) will stop blinking
indicating the cleaner is ready for use.
5. Select the desired steam intensity, LOW or HIGH, according to the surface to
clean. [17]
6. Press the trigger underside of the portable steam handheld handle to release the
steam. [18]
PORTABLE STEAM HANDHELD ACCESSORIES
NOTE: All accessories can only be attached to the Refresh Conical pipe (Y) and
cannot be connected directly to the product or the hose.
The refresh conical pipe allows you to a longer steaming time. It is advised for delicate
surfaces and for longer cleaning sessions. The following accessories can be connected
directly to it:
Comb Nozzle: Ideal for removal of limescale and grime. [19]
Copper Round Brush: Ideal for removal of baked on grease from ovens' racks. [20]
Shovel Plate: Ideal for removal of stubborn stains. [21]
Curved Nozzle: Ideal for cleaning hard to reach areas such as taps etc. [22]
Small Round Brush: Ideal for use on stubborn grease and grime. [23]
Multi-Purpose Nozzle: this is used along with the Large scraper, Textile pad and Refresh
tool.
1. Refresh Tool: Insert the multi- purpose tool into refresh tool, ideal for use on
garments and textiles. [24]
2. Large Scraper: Insert the multi-purpose nozzle into the large scraper, which is ideal
for use on windows and mirrors for smear clean free finish. [25]
3. Textile Pad: Fit the textile pad over the multi- purpose nozzle, ideal for cleaning
fabric and soft furnishings. [26]
IMPORTANT: As the accessories become very hot during use, you must be very careful
when removing them or replacing them. Either use an oven glove to handle them or wait
until they cooled down. Always ensure that the product is disconnected from the mains
power before changing the accessories.
USING THE VACUUMING ACCESSORY MODE
The product is provided with convenient accessories to vacuum high and difficult to reach
areas [28]:
Extension Hose
Rigid Long Tube
3in1 Accessory
1. Unwind power cord from cord storage hooks and plug it into power supply. Clip
power cord in the cord clip at the back of the handle.
2. Open vacuum hose connection cover at the back of the product [27], insert the
extension hose and rotate it until it is blocked in position.
Switch the cleaner on by pressing the On/Off button on handheld. [6]
3.
4. Switch the Vacuum on by pressing the Vacuum on/off button located on the main
handle. [10]
5. Attach the rigid long tube to the end of the hose to enhance the reach of your
cleaning. [28]
Attach the 3in1 accessory to the rigid long tube or directly to hose to clean. [28]
6.
3
GB