Reducing Dust Exposure: - Metabo S 18 LTX 115 Manual De Instrucciones

See page 3 and chapter 14. Technical
Specifications for more information on the spindle
length and thread.
Damaged, eccentric or vibrating tools must not be
used.
A damaged or cracked side handle must be
replaced. Never operate a machine with a defective
side handle.
Only use the machine if the protective cover is in
place.
Always guide the machine with both hands on the
handles provided
4.7 Special safety instructions for mains
powered machines:
Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
Before connecting the mains plug, make sure that
the machine is switched off.
Use of a fixed extractor system is recommended.
Always install an RCD with a maximum trip current
of 30 mA upstream. If the angle grinder is shut down
via the RCD, it must be checked and cleaned. See
Chapter 9. Maintenance.
4.8 Special safety instructions for cordless
machines:
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Make sure that the tool is switched off before fitting
the battery pack.
Protect battery packs from water and
moisture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short circuit battery pack contacts!
A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
If the machine is defective, remove the battery pack
from the machine.
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
4.9

Reducing dust exposure:

Some of the dust created using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some of these
substances include: lead (in paint containing lead),
mineral dust (from bricks, concrete etc.), additives
used for wood treatment (chromate, wood
preservatives), some wood types (such as oak or
beech dust), metals, asbestos.
The risk from exposure to such substances will
depend on how long you or bystanders are being
exposed.
Do not let particles enter the body.
Do the following to reduce exposure to these
substances: ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to filter
microscopically small particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see
chapter 11.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash protective clothing Do not blow,
beat or brush.
5. Overview
See page 2.
1 Additional handle
2 Safety cover
3 Handle bar
4 Clamping lever
5 Screw
6 Handle
7 Sliding on/off switch
(S 18 LTX 115)
8 Spindle locking button
9 Spindle
10 Electronic signal indicator
11 Speed adjustment wheel
(SE 17-200 RT)
12 Trigger switch (SE 17-200 RT)
13 Tool fixing screw
14 Tensioning spindle (with 2 captive fitted keys)
ENGLISH en
13