Mitsubishi Electric PLK-G Serie Manual Tecnico página 168

CODE
M-215 WRITING SEWING DATA INTO THE INTERNAL MEMORY...
M-216 DELETING SEWING DATA IN THE INTERNAL MEMORY...
M-217 READING SEWING DATA FROM THE INTERNAL MEMORY...
M-218 DELETES SEWING DATA IN THE INTERNAL MEMORY
M-219 OVERWRITES SEWING DATA IN THE INTERNAL MEMORY
M-220 INSUFFICIENT EMPTY AREA IN THE INTERNAL MEMORY
M-222 PATTERN DATA CAN NOT BE DELETED
M-223 FORMATS INTERNAL MEMORY
M-224 OPTIMIZES INTERNAL MEMORY
M-226 COMBINATION DATA CAN NOT BE CREATED
M-227 CAN NOT CHANGE PATTERN DATA NUMBER
M-228 OUT OF AREA LIMIT
M-230 CAN NOT READ
M-231 CAN NOT WRITE
M-232 TOO MANY STITCHES
M-234 ILLEGAL FILE NAME
M-235 ILLEGAL PATTERN NUMBER
M-237 CHANGE PATTERN DATA TO G-DATA
M-238 INCORRECT PASSWORD
M-240 CAN NOT READ COMBINATION PATTERN
M-246 NEEDLE IS NOT CORRECT POSITION
M-247 TRIMMING OUTPUT WAS CANCELED
M-248 TENSION RELEASE OUTPUT WAS CANCELED
M-274 CAN NOT USE COMBINATIONAL FUNCTION.
M-275 CAN NOT READ, BECAUSE THE COMBINATION IS BEING USED
M-276 INCORRECT NUMBER OF PATTERN DATA
M-277 COPIES REGISTERED SEWING DATA
M-278 DELETES COMBINATIONAL SEWING DATA
M-279 DELETES DOCKING SEWING DATA
M-280 COPYING SEWING DATA FROM USB MEDIUM TO THE MEMORY...
M-281 COPYING SEWING DATA FROM THE MEMORY TO USB MEDIUM...
M-283 COPY FAILED
M-287 ILLEGAL SETTING
M-288 THERE IS NO DIFFERENCE
M-289 PATTERN DATA DOES NOT EXIST
M-290 READING COMPLETE
M-291 READING SETTING FILE...
M-292 READING STEP FILE...
M-293 READING SYSTEM FILE...
M-294 CURRENT USED TABLE IS OVERWRITTEN
M-295 COPIES SPECIFIED PATTERN DATA
MESSAGE
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON
PLEASE ERASE UNUSED PATTERN
CURRENT PATTERN DATA CAN NOT BE ERASED
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON (SEWING DATA WILL NOT BE ERASED)
No: X ICON
PATTERN DATA WHICH CONTAINS SECOND HOME POSITION CAN NOT BE USED FOR
COMBINATION.
CAN NOT CHANGE TO PATTERN DATA NUMBER WHICH IS USING.
PLEASE CHANGE PATTERN DATA
PRESS HOME ICON
PRESS HOME ICON
PLEASE CHANGE PATTERN DATA
PLEASE INPUT THE FILE NAME BY 8 CHARACTERS OR LESS
PLEASE INPUT CORRECT SEWING DATA NUMBER.
ARE YOU SURE? Yes: ENTER ICON
No: X ICON (BACK TO SELECTION SCREEN)
PLEASE INPUT AGAIN
PLEASE CLEAR COMBINATION PATTERN (PRESS CLR ICON)
PLEASE ADJUST UP POSITION SENSOR OR [U8] SETTING
PLEASE ADJUST TRIMMING START TIME/ANGLE [TRS]
PLEASE ADJUST TENSION RELEASE START TIME/ANGLE [LRS]
DISABLE THE FUNCTION OF PATTERN SELECTION BY USING OF EXTERNAL SIGNAL
PLEASE ENTER THE COMBINATION MODE ON FUNCTION MODE AND PRESS THE CLR ICON
TO DEACTIVATE THE COMBINATION FUNCTION
CAN NOT CHANGE TO FORMER SERIESE NUMBER OF PATTERN DATA
ARE YOU SURE? Yes: ENTER ICON
No: X ICON
*IF THERE IS SAME NUMBER IN THE MEMORY,DATA IS OVERWRITTEN
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
SOME SEWING DATA WERE NOT COPIED COMPLETELY. PLEASE CHECK THAT COPIED
SEWING DATA.
PLEASE SELECT SETTING FILE THAT IS CREATED ON SAME SEWING MACHINE MODEL
PLEASE TURN OFF THE POWER. PLEASE RE-TURN ON THE POWER AFTER POWER LED
(GREEN) OF THE CONTROL BOX IS TURNED OFF.
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON
*IF THERE IS SAME NUMBER IN THE MEMORY,DATA IS OVERWRITTEN
165
SUB-MESSAGE
No: X ICON
No: X ICON
DATA, AND OPTIMIZE AN INTERNAL MEMORY.
No: X ICON
No: X ICON
No: X ICON
No: X ICON
No: X ICON