Additional Safety Rules For Tool; Bench Mounting; Functional Description - Makita MLS100 Manual De Instrucciones

only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
ADDITIONAL SAFETY RULES
FOR TOOL
1. Wear eye protection.
2. Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still cause
severe injury.
3. Do not operate saw without guards in place.
Check blade guard for proper closing before each
use. Do not operate saw if blade guard does not
move freely and close instantly. Never clamp or tie
the blade guard into the open position.
4. Do not perform any operation freehand. The
workpiece must be secured firmly against the turn
base and guide fence with the vise during all
operations. Never use your hand to secure the
workpiece.
5. Never reach around saw blade.
6. Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
7. Unplug tool before changing blade or servicing.
8. Do not use the tool in the presence of flammable
liquids or gases.
9. Check the blade carefully for cracks or damage before
operation. Replace cracked or damaged blade
immediately.
10. Use only flanges specified for this tool.
11. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt. Damage to
these parts could result in blade breakage.
12. Make sure that the turn base is properly secured so it
will not move during operation.
13. For your safety, remove the chips, small pieces, etc.
from the table top before operation.
14. Avoid cutting nails. Inspect for and remove all nails
from the workpiece before operation.
15. Make sure the shaft lock is released before the switch
is turned on.
16. Be sure that the blade does not contact the turn base
in the lowest position.
17. Hold the handle firmly. Be aware that the saw moves
up or down slightly during start-up and stopping.
18. Make sure the blade is not contacting the workpiece
before the switch is turned on.
19. Before using the tool on an actual workpiece, let it run
for a while. Watch for vibration or wobbling that could
indicate poor installation or a poorly balanced blade.
20. Wait until the blade attains full speed before cutting.
21. Stop operation immediately if you notice anything
abnormal.
22. Do not attempt to lock the trigger in the on position.
23. Be alert at all times, especially during repetitive,
monotonous operations. Do not be lulled into a false
sense of security. Blades are extremely unforgiving.
24. Always use accessories recommended in this manual.
Use of improper accessories such as abrasive wheels
may cause an injury.
25. Do not use the saw to cut other than wood,
aluminum or similar materials.
8
26. Connect miter saws to a dust collecting device
when sawing.
27. Select saw blades in relation to the material to be
cut.
28. Take care when slotting.
29. Replace the kerf board when worn.
30. Do not use saw blades manufactured from high
ENB040-3
speed steel.
31. Some dust created from operation contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based-painted material and,
• arsenic and chromium from chemically-treated
lumber. Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area and
work with approved safety equipment, such as
those dust masks that are specially designed to
filter out microscopic particles.
32. To reduce the emitted noise, always be sure that
the blade is sharp and clean.
33. The operator is adequately trained in the use,
adjustment and operation of the machine.
34. Use correctly sharpened saw blades. Observe the
maximum speed marked on the saw blade.
35. Refrain from removing any cut-offs or other parts
of the workpiece from the cutting area whilst the
tool is running and the saw head is not in the rest
position.
SAVE THESE INSTRUCTIONS.
INSTALLATION (Fig. 1 & 2)
When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. Loosen the bolt with a
wrench provided with the tool and move the saw head to
the right angle. Remove the bolt and secure the saw head
with the knob.
Installing auxiliary plate (Fig. 3)
Installing the auxiliary plate using the hole in the tool's
base and secure it by tightening the screw.

Bench mounting

When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. Release the stopper
pin by lowering the handle slightly and pulling the stopper
pin. (Fig. 4)
This tool should be bolted with four bolts to a level and
stable surface using the bolt holes provided in the tool's
base. This will help prevent tipping and possible injury.
(Fig. 5)

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.