cam IDEA S334 Instrucciones De Uso página 18

INSTRUCTIONS FOR USE
IMPORTANT INFORMATION
• Read carefully these instructions and retain
them for future reference. • Cam il mondo del
bambino reserves all the rights to amend the
product for technical or commercial reasons.
• Always use the product as it has been conceived;
on the contrary the producer will not be held
responsible for any misuse. Do not use if
components or fittings are worn, damaged or
missing. In this case, do not use replacement parts
other than those recommended or supplied by the
manufacturer. • Use this product only on a chair
with larger dimensions than those of the booster
seat itself. • This product isn't recommended for
babies who can't sit by themselves. • Make sure
that both the floor and the chair surface are flat
before using the product. • Once the booster seat
is on the chair, verify the stability of the product
on the chair. • Never use this product on a stool,
an unstable chair, a folding chair, padded chairs or
particularly shaped chairs. • Never leave your child
unattended in this product. • Use the safety
harness at all times. • Use this product only on a
chair and with all the restraining system and
safety harness locked as described in the
instruction leaflet.
INSTRUCTIONS FOR USE:
1. ANTI SLIP FEET: insert them firmly as shown in
the figure.
2. OPENING THE PRODUCT: grip the backrest and
push at the same time the seat unit downwards till
you hear a "click" and the chair is open.
3. ASSEMBLING THE LOWER STRAP: place the
chair booster seat upside down. Insert the strap in
the two side slots on the chair booster base, as
shown in the figure.
4. ASSEMBLING THE REAR STRAP: assemble the
straps as shown in the diagram.
5a-d. ASSEMBLING THE 3 POINT HARNESS AND
THE SEAT PAD.
6a-e. ASSEMBLING
(OPTIONAL) AND THE SEAT PAD.
7a. ADJUSTING THE BOOSTER SEAT HEIGHT:
place a hand on the booster seat base, at the same
time lift the backrest upwards till it reaches the
required position.
7b. LOWERING THE BOOSTER SEAT: push the button
on the booster seat base, pull at the same time the
lever and lower the booster seat down.
WARNING! DO NOT LOWER THE BOOSTER SEAT WITH
THE CHILD INSIDE!
8. FITTING THE BOOSTER SEAT TO A CHAIR:
8a. Place the booster seat centrally in the chair's seat
(1) and make sure that the chair's seat has a bigger
surface than the booster seat itself. Pass the base
attachment straps (2) under the chair's seat and lock
the buckle (3). Tighten the belt (4). Fasten the rear
booster seat strap around the back of the chair (5)
and lock the buckle (6). Tighten the belt (7).
8b. Place your child on the booster seat. Fasten the
belts and adjust them. After adjusting the seat height,
17
THE 5 POINT HARNESS
please check the rear harness is correctly tightened.
WARNING: CHECK THAT THE BOOSTER SEAT IS
SECURELY FITTED TO THE CHAIR'S SEAT TO AVOID
ANY MOVEMENT OF THE BOOSTER SEAT.
9a. FITTING THE TRAY (OPTIONAL): insert the 2
plastic tabs of the tray on the armrests slots, then fit
the 2 side buttons.
9b. REMOVING THE TRAY: push both the 2 side
buttons and remove the tray.
10a. HIGHCHAIR MODE: for younger children.
10b. BOOSTER SEAT MODE: for older children.
11a. FOLDING THE BOOSTER SEAT: remove the tray
and adjust to the lower position the seat. Unfasten all
harnesses. Push the button on the booster seat base,
at the same time pull the lever and push the seat unit
towards the backrest till it clicks in position.
11b. OPTIONAL: fit the booster seat tray as shown in
the figure.
11c. Lock the rear attachment straps and then the
base attachment straps (as shown in the figure) to
avoid any unexpected opening of the product. Thanks
to the integrated carrying handle, it is very easy to
carry the product around.
12. CARE AND MAINTENANCE:
Prolonged exposure to the sun and inadequate
washing can cause the fabric and the plastic colours
to change. Limit exposure if possible. Dry all metal
parts to prevent rust. Never leave the product near
any source of strong heat (electrical heating or gas
heating) to avoid fire danger.
Clean the product with a damp cloth or sponge and
mild detergent. Do not use abrasive.
The fabric cover is hand washable in warm water (max
30 °C) with mild detergent (do not bleach). Do not use
dryers, do not dry clean, do not iron. To remove it
release the buttons and take the fabric cover away
from the booster seat.
13. SPARE PARTS:
N. CODE DESCRIPTION
01 S334/01 rear attachment strap
02 S334/02 block-system for
adjustable height
03 S334/03 seat plastic pin
04 S334/04 backrest plastic pin
05 S334/05 armrest button
06 S334/06 armrest plastic pin
07 S334/07 safety button
08 S334/08 anti slip feet
09 S334/09 instruction manual
10 S334/10 seat cover
11 S334/11 3 point harness
12 S334/12 tray logo (optional)
13 S334/13 tray (optional)
14 S334/14 5 point harness (optional)
THIS PRODUCT COMPLIES WITH SAFETY
REQUIREMENTS FOLLOWING X PS 54-041