Troubleshooting - Insignia NS-H3005 Guia Del Usuario

Insignia NS-H3005 Home Theater System
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints
will not get on the surface.
Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or
sources of heat, or leave it in a parked car
exposed to direct sunlight, because it may get
very hot inside the car.
Cleaning discs
Fingerprints and dust on the disc can cause
poor picture quality and sound distortion. Before
playing, clean the disc with a clean cloth. Wipe
the disc from the center outward.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.

Troubleshooting

Check the following guide for the possible cause
of a problem before contacting service.
Symptom Cause
No power The power cord is
disconnected.
The power is on, No disc or tape is
but the home inserted.
theater system
does not work.
No picture The television is not
set up to receive
home theater system
signal output
TV/VCR mode for
home theater system
is set to TV.
The video cable is not
connected securely.
The connected
television is turned
off.
No sound. The Digital Audio
Output is set to the
wrong position.
Correction
Securely plug the
power cord into the
wall outlet.
Insert a disc or tape.
Make sure that the disc
or tape indicator on the
display window is lit.
Select the appropriate
video input mode on
the television so the
picture from the player
appears on the
television screen.
Press the TV/VCR
button on the remote
control repeatedly to
choose VCR mode.
The TV indicator
disappears from the
display window.
Connect the video
cable securely.
Turn on the television.
Set the Digital Audio
Output to the correct
position, then turn on
the home theater
system again by
pressing POWER.
www.insignia-products.com
Symptom Cause
The playback The disc is dirty.
picture is poor.
Video heads are dirty. Clean video heads.
Tape is a rental or was
recorded on
another VCR.
The home theater No disc or tape is
system does not inserted.
start playback.
An unplayable disc is
inserted.
The disc is placed
upside down.
The disc is not placed
within the guide.
The disc is dirty.
The remote The remote control is
control does not not pointed at the
work properly. remote sensor of the
home theater system.
The remote control is
too far from the home
theater system.
There is an obstacle
in the path of the
remote control and
the home theater
system.
The batteries in the
remote control are
exhausted.
This remote control
uses the same
buttons for VCR and
DVD functions (ex.
PLAY).
Some channels Those channels were
are skipped over deleted with the CH.
when using ADD/DEL option.
/
Picture and Antenna or cables are
sound of loose.
broadcasting
Wrong TUNING BAND
channel
option is being used.
are weak or
missing.
Camcorder image Home theater system
via A/V input to SOURCE SELECT is
home theater not set to LINE1 or
system is not LINE2.
shown on
television screen.
Timer recording Clock in home theater
is not possible. system is not set to
correct time.
Timer has been
programmed
incorrectly.
indicator does not
appear after
programming timer.
Correction
Clean the disc.
Press / for
manual tracking
adjustment while tape
is playing.
Insert a disc or tape.
(Check that the disc or
tape indicator in the
display window is lit.)
Insert a playable disc.
(Check the disc type,
color system, and
Regional code.)
Place the disc with the
label side up.
Place the disc on the
disc tray correctly
inside the guide.
Clean the disc.
Point the remote
control at the remote
sensor of the home
theater system.
Operate the remote
control within 23 ft
(7 m) of the home
theater system.
Remove the obstacle.
Replace the batteries
with new ones.
When using a VCR
tape, first press the
VCR button. When
using a DVD, first
press the DVD button.
Press CH. ADD/DEL.
to restore channels.
See "Channel
Selection" on page 12.
Tighten connections or
replace cable.
Try all TUNING BAND
options. See "Channel
Selection" on page 12.
Press INPUT to select
LINE input source
(LINE1 or LINE2).
Set clock to correct
time. See "Setting the
clock" on page 13.
Reprogram Timer. See
"Timer Recording" on
page 20.
Reprogram the timer.
31