Important Safety Instructions - Hamilton Beach Tempest Serie Manual De Uso

Ocultar thumbs Ver también para Tempest Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

IMPORTANT SAFETY INSTRUCTIONS

WARNING –
When using electrical appliances, basic safety precautions should be followed, including
the following:
• Read all instructions.
• Plug into a grounded outlet.
• Do not touch surfaces that may be hot.
Use handles or knobs provided.
• Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
• Do not use appliance for other than intended use.
• To protect against electrical shock, do not
immerse cord, plug, or blender base in water
or any other liquid.
• Close supervision is necessary when any
appliance is used by or near children.
• The use of accessory attachments not recom-
mended by Hamilton Beach may cause injuries.
• To reduce risk of personal injury, unplug cord
from outlet when not in use, and before putting on
or taking off parts or doing any other servicing of
the blender.
• Do not let cord hang over edge of table or
counter or touch hot surfaces.
• Do not place on or near a hot gas or electric
burner or in a heated oven.
• To reduce risk of personal injury and to prevent
damage to blender or jar and cutter assembly,
DO NOT insert utensils into blender jar while
operating blender, or store utensils in the blender
jar when it is not in use.
• Avoid contacting moving parts.
• Blades are sharp. Handle carefully.
• Inspect jar and cutter assembly daily. Check
cutter for wear, nicks, or broken blades. Replace
jar and cutter assembly at least every 12 months.
• Do not defeat the jar pad sensors.
• Do not use outdoors.
• This appliance is intended for short periods
of operation, with a rated operating time of
3 minutes.
Blender Operation – Quick Start Guide
1.
Place the blender on a dry, level surface.
2.
Make sure the power switch is in the "off" or O
position. Plug the blender into a grounded electrical
outlet.
3.
Place the jar on the base with ingredients and jar
lid in place.
SAVE THESE INSTRUCTIONS
• To prevent damage to blender, jar, or cutter
assembly, DO NOT move or shake blender
while in operation. If blending action stops during
operation, turn blender OFF, remove jar from
base, remove jar cover, and use a thin rubber
spatula to push mixture towards cutters.
• Do not spray the base with a high-pressure
spray gun.
• Disconnect power before cleaning or servicing.
• To prevent burns from hot liquids splashing out
of the jar, always remove the filler cap of the
container cover before blending hot liquids.
• Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions,
or is dropped or damaged in any manner.
Return appliance to the nearest service facility
for examination, repair, or electrical or
mechanical adjustment.
• If the supply cord of this appliance is damaged,
it must be replaced by the manufacturer or its
service agent or a similar qualified person. If fitted
with a non-rewirable U.K. plug, the 13 amp fuse
approved by ASTA to be B.S. 1362 must be used.
If you need a replacement fuse carrier, it must be
replaced by the same colour coded carrier with
the same markings. Fuse covers and carriers
can be obtained from approved service agents.
IMPORTANT: If the molded plug is cut off,
dispose of it immediately. The plug is not rewirable
and would cause a shock hazard if inserted into
a socket.
• For a complete operation manual in this
language, please visit our website at
www.commercial.hamiltonbeach.com
or call 910-692-2223.
4.
Set the controls to your preference.
5.
Move the power switch to the "on" or I position
(except model 915).
6.
Move the power switch to start (run) or
position.
Blender Safety
3

Publicidad

Tabla de contenido
loading

Tabla de contenido