DeWalt DCS571 Manual De Instrucciones página 14

English
guard using the lower guard blade retracting
lever then releasing it from the fully open
position. If the guard does not operate smoothly,
close quickly or completely then do not use the
saw and contact your D
repairs. If the lower blade guard is missing or not
working properly, have the saw serviced before
using. To assure product safety and reliability,
repair, maintenance and adjustment should
be performed by an authorized service center
or other qualified service organization, always
using identical replacement parts.
Kerf Indicator (Fig. A, M)
The front of the saw shoe has a kerf indicator
and bevel cutting. This indicator enables you to guide the
saw along cutting lines penciled on the material being
cut. The kerf indicator lines up with the left (outer) side of
the saw blade, which makes the slot or "kerf" cut by the
moving blade fall to the right of the indicator. Guide along
the penciled cutting line so that the kerf falls into the waste
or surplus material. To adjust the kerf indicator
the kerf indicator screw 28 with the blade wrench
move the indicator left or right as needed. Tighten screw
when finished adjusting the indicator.
Fig. M
28
Workpiece Support (Fig. J, N–P)

WARNING: It is important to support the work
properly and to hold the saw firmly to prevent loss of
control which could cause personal injury. Figure J
illustrates proper hand support of the saw. Maintain
a firm grip with both hands on the saw and position
your body and arm to allow you to resist kickback
if it occurs. ALWAYS TURN OFF TOOL AND REMOVE
BATTERY BEFORE MAKING ANY ADJUSTMENTS!
Fig. N
Figure N shows proper sawing position. Note that hands
are kept away from cutting area. To avoid kickback, DO
support board or panel NEAR the cut (Fig. O). DON'T support
board or panel away from the cut (Fig. P).
12
WALT service center for
e
for vertical
10
10 , loosen
14 and
10
Place the work with its "good" side – the one on which
appearance is most important – down. The saw cuts
upward, so any splintering will be on the work face that is
up when you cut it.
Fig. O DO support board or panel NEAR the cut.
SUPPORT
Fig. P
DON'T support board or panel AWAY from the cut.
Cutting (Fig. N)
Place the wider portion of the saw shoe on that part of the
workpiece which is solidly supported, not on the section
that will fall off when the cut is made. As an example,
Figure N illustrates the RIGHT way to cut off the end of a
board. Always clamp work. Don't try to hold short pieces by
hand! Remember to support cantilevered and overhanging
material. Use caution when sawing material from below.
Be sure saw is up to full speed before blade contacts
material to be cut. Starting saw with blade against material
to be cut or pushed forward into kerf can result in kickback.
Push the saw forward at a speed which allows the blade to
cut without laboring.
Hardness and toughness can vary even in the same piece of
material, and knotty or damp sections can put a heavy load
on the saw. When this happens, push the saw more slowly,
but hard enough to keep working without much decrease
in speed. Forcing the saw can cause rough cuts, inaccuracy,
kickback, and over-heating of the motor.
Should your cut begin to go off the line, don't try to force
it back on. Release the trigger switch and allow blade to
come to a complete stop. Then you can withdraw the saw,
sight anew, and start a new cut slightly inside the wrong
one. Withdraw the saw if you must shift the cut. Forcing
a correction inside the cut can stall the saw and lead
to kickback.
IF SAW STALLS, RELEASE THE TRIGGER SWITCH AND
BACK THE SAW UNTIL IT IS LOOSE. BE SURE BLADE IS
STRAIGHT IN THE CUT AND CLEAR OF THE CUTTING EDGE
BEFORE RESTARTING.
As you finish a cut, release the trigger switch and allow the
blade to stop before lifting the saw from the work. As you
lift the saw, the spring-tensioned lower blade guard will
automatically close under the blade. Remember the blade