Operation - Hayward LPCUS11 Serie Manual De Uso

Universal ColorLogic Light modes
The Hayward Universal ColorLogic light is designed to operate in one of four modes; Universal ColorLogic, ColorLogic 4.0, ColorLogic 2.5 & earlier and Pentair
SAM.
ColorLogic lights can also be used in Networked mode or Omni Direct mode. Networked mode requires a Pro Logic pool controller and Hayward AQL-COLOR-
MODHV modem (page 13). For Omni Direct mode, the lights must be built after June 2018 and used with an OmniLogic or OmniHub pool controller (page 13).
Universal ColorLogic mode (default): The light is shipped in this mode. Use this mode for new installations and for installations with other Universal Col-
orLogic lights.
ColorLogic 4.0 mode: Use this mode when installing your new light in systems with ColorLogic 4.0 lights. The Universal ColorLogic light will be "seen" as
another ColorLogic 4.0 light and will operate in the same manner as the others.
ColorLogic 2.5 & earlier mode: Use this mode when installing your new light in systems with ColorLogic 2.5 & below lights. The Universal ColorLogic light
will be "seen" as another ColorLogic 2.5 & earlier light and will operate in the same manner as the others.
Pentair SAM: Use this mode when installing your new light in systems with Pentair SAm
another Pentair SAm ® /SAL ® light and will operate in the same manner as the others.
Omni Direct mode: Omni Direct mode offers unique colors as well as speed and brightness control. It must be configured and controlled by a Hayward Omni-
Logic or OmniHub pool controller only. Refer to the controller's manual for more information.
How to change modes:
1. Turn on lights and then turn off for between 11-15 seconds.
2. Turn on lights and then turn
3. Turn on lights and then turn off for between 11-15 seconds.
4. The light should blink one of 5 colors indicating which mode it is currently in. Refer to the table below to determine which mode the Universal ColorLogic
is in. Note that new lights are shipped from the factory in Universal ColorLogic mode (blinking red).
5. To change modes, turn light off and back on. The light will then advance to the next mode. Continue this method until you arrive at the desired mode.
6. When the light is in the desired mode, remove power from the lights for at least one minute.
7. The light will restart in the new mode the next time it is turned on.
CrystaLogic Light Dimming (White Light)
The CrystaLogic light can be adjusted to operate at different light intensities. To change light intensity, follow the procedure below.
1. Turn on lights and then turn off for between 11-15 seconds.
2. Turn on lights and then turn off for between 11-15 seconds.
3. Turn on lights and then turn off for between 11-15 seconds.
4. The light will blink indicating which mode it is currently in:
•
Mode 1 (1 blink) - 100% intensity
•
Mode 2 (2 blinks) - 60% intensity
•
Mode 3 (3 blinks) - Variable intensity, Once the desired mode is saved, the user may select among 5 brightness levels by briefly toggling power (100%,
80%, 60%, 40%, 20%, 40%, 60%, 80%, 100%, 80%, etc. )
5. To change modes, turn light off and back on. The light will then advance to the next mode. Continue this method until you arrive at the desired mode.
6. To save, remove power from the lights for at least one minute.
7. The light will restart in the new mode the next time it is turned on.
12
off for between 11-15 seconds.
MODE
Universal ColorLogic
ColorLogic 4.0
ColorLogic 2.5
Pentair SAM
Omni Direct
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Operation

or SAL
® ®
COLOR
Red
Green
Blue
White
Purple
lights. The Universal ColorLogic light will be "seen" as