Kickback And Related Warnings; Safety Warnings Specific For Grinding Operations; General Safety Instructions For Grinders - Hitachi G 14DSL Manual De Instrucciones

Ocultar thumbs Ver también para G 14DSL:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The
wheel may either jump toward or away from the
operator, depending on direction of the wheel's
movement at the point of pinching. Abrasive wheels
may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can
be avoided by taking proper precautions as given below.
a)
Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided,
for maximum control over kickback or torque
reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b)
Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c)
Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite
to the wheel's movement at the point of snagging.
d)
Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory.
Corners, sharp edges or bouncing have a tendency
to snag the rotating accessory and cause loss of
control or kickback.
e)
Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
SAFETY WARNINGS SPECIFIC FOR
GRINDING OPERATIONS
a)
Use only wheel types that are recommended for
your power tool and the specific guard designed
for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
b)
The grinding surface of centre depressed wheels
must be mounted below the plane of the guard
lip.
An improperly mounted wheel that projects
through the plane of the guard lip cannot be
adequately protected.
6
c)
The guard must be securely attached to the power
tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the
operator.
The guard helps to protect operator from broken
wheel fragments, accidental contact with wheel
and sparks that could ignite clothing.
d)
Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral
grinding, side forces applied to these wheels may
cause them to shatter.
e)
Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus
reducing the possibility of wheel breakage. Flanges
for cut-off wheels may be different from grinding
wheel flanges.
f)
Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable
for the higher speed of a smaller tool and may
burst.
GENERAL SAFETY INSTRUCTIONS FOR
GRINDERS
Check that speed marked on the wheel is equal to
or greater than the rated speed of the grinder;
Ensure that the wheel dimensions are compatible
with the grinder;
Abrasive wheels shall be stored and handled with
care in accordance with manufacturer's
instructions;
Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products;
Ensure that mounted wheels and points are fitted
in accordance with the manufacturer's instructions;
Ensure that blotters are used when they are
provided with the bonded abrasive product and
when they are required;
Ensure that the abrasive product is correctly
mounted and tightened before use and run the tool
at no-load for 30 s in a safe position, stop
immediately if there is considerable vibration or if
other defects are detected. If this condition occurs,
check the machine to determine the cause;
If a guard is equipped with the tool never use the
tool without such a guard;
Do not use separate reducing bushings or adapters
to adapt large hole abrasive wheels;
For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length;
Secure the workpiece and check that the workpiece
is properly supported. A workpiece clamped with
clamping devices or in a vice is held more securely
than by hand;
Do not use cutting off wheel for side grinding;

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

G 18dsl

Tabla de contenido