Function Descriptions; Water Drainge - Whirlpool DE 20 LWS0 Manual Del Usuario

Use & Care Guide

FUNCTION DESCRIPTIONS

TIMER FUNCTION
Dry
Timer
increments to between 0 and 24 hours whenever the Timer
button is pressed . After pressing and holding the Timer
button, the time will increase .
Setting the Timer ON function
The Timer ON function can be set when the appliance is in the
OFF status . Press the Timer button: the button background will
light up and "00h" will appear on the display panel (1); within 5
seconds, you can press the Timer button to select the desired
time when the appliance must switch on . Once the timer has
been set, the time will be displayed for 5 sec, the Timer ON/
OFF indicator will be on and the display panel will switch off .
The appliance will switch on automatically at the chosen time .
NOTE: If the time is not set within 5 seconds after pressing the
Timer button, the appliance will exit the Timer function .
Cancelling the Timer ON function
Press the Timer button again to enter the function: after the
button background lights up, press the Timer button until
the appliance displays "00h" and the Timer ON/OFF indicator
disappears . The function will have been cancelled .
Setting the Timer OFF function
The Timer OFF function can be set when the appliance is in
the ON status . Press the Timer button: the button background
lights up and "00h" appears on the display panel (1); within 5
seconds, press the Timer button to select the desired time for
the appliance to switch off . After the timer is set, the time will be
displayed for 5 sec and the Timer ON/OFF indicator turns on .
The appliance will switch off automatically at the chosen time .
RESETTING THE FILTER
+
Timer ON/OFF
Fan Humidity
filter, press the Fan and Humidity buttons simultaneously and
the filter indicator will turn off .
The air filter should be cleaned whenever the appliance signals
this need, so that the unit's performance does not deteriorate .
WATER DRAINAGE
DRAINING WATER THROUGH THE WATER BUCKET
The Water Full indicator lights up when the water bucket is full . The machine stops automatically and the water bucket will
have to be emptied .
Press the Timer button
to switch the timer on
Timer ON/OFF
or off . The timer can be
set with 1h (one hour)
When the Clean Filter
indicator lights up, the
Filter Clean
filter needs cleaning .
After cleaning the air
1. Remove the water bucket
Pull the water bucket out by gripping both of its sides .
► Do not remove the sensor (19) on the water bucket used to measure the water level, as
water may leak out, thus damaging the unit and causing possible electric shock .
► The dirty water bucket can be washed using cold or warm water . Do not use solvents,
abrasiveproducts, petrol, chemicals, cloths or other materials to clean the bucket, as
these may damage it and cause water leakages .
CHILD LOCK FUNCTION
+
Mode Timer
function . "LC" will appear on the display panel to signal that
the buttons are locked, and the Mode and Timer buttons
will flash for a few seconds . No functions can be activated by
pressing the buttons .
Press the Mode and Timer buttons simultaneously once again
to unlock this function, the Mode and Timer buttons will flash
for a few seconds .
This function can be used when the appliance is switched
both off and on .
AUTO STOP FUNCTION
When the bucket is full, removed or not correctly inserted in
the unit, or when the humidity level is 5% lower than the set
humidity, the unit will stop operating automatically .
MEMORY FUNCTION
In case of a power failure, all settings will be memorised . Once
the power supply is restored, the unit will resume operating
according to the memorised settings .
WATER BUCKET FULL FUNCTION
If the water bucket is full or has been removed for over 3
minutes, the Water Full indicator will light up and emit a
"beep" . The machine will resume operating once the water has
been drained and the bucket has been re-inserted .
AUTO POWER OFF
In Cont mode, the machine stops automatically when the
water bucket is full, the same occurs when the water bucket is
extracted or is incorrectly positioned .
AUTO DEFROST
During operation, the compressor will stop automatically
when frost covers the evaporator . The fan will run continuously
until the defrosting process terminates . The machine will then
restart automatically .
EN
Mode
Press the
Timer
and buttons
simultaneously to
activate the child lock
21