Maintenance; Sharpening The Saw Chain; Replacing The Power Cable; Cleaning, Storage And Ordering Of Spare Parts - Gardol GETS-E 710 Kit Manual De Instrucciones Original

Warning!
•
Make sure that the chain tension is always
correctly adjusted.
•
Only use a chainsaw if it is in perfect working
order.
•
Only work with a saw chain that has been
properly sharpened in accordance with the
instructions.
•
Never cut with the upper edge or the tip of the
cutter rail.
•
Always hold the chainsaw firmly with both
hands.
Cutting wood which is under tension
Danger!
Special care is required when cutting wood which
is under tension. Wood which is under tension
from which it is released by cutting may in some
cases react completely unpredictably and un-
controllably. In the worst case this could result in
extremely severe or even fatal injuries. This type
of work must only be performed by persons who
have been specially trained.

8. Maintenance

8.1 Replacing the saw chain and cutter rail
The cutter rail needs to be replaced if
the guide groove of the cutter rail is worn;
Proceed as described in the section "Assembly of
the cutter rail and the saw chain".
Note:
Use the „Oregon 084LNEA041" cutter bar only
in combination with the „Oregon 90JG033X"
or „90PX033X" saw chain, and the „Oregon
080NDEA041" cutter bar only in combination with
the „Oregon 91P033X" saw chain.
8.2 Checking the automatic chain lubrication
You should check the operation of the automatic
chain lubrication system on a regular basis in or-
der to guard against overheating and the associ-
ated damage to the cutter rail and the saw chain.
To do this, point the tip of the cutter rail towards
a smooth surface (board, section of a cut tree)
and allow the chainsaw to run. If an increasing oil
trace becomes evident during this process then
the automatic chain lubrication system is working
properly. If no clear oil trace is evident then please
refer to the corresponding instructions in "Troub-
leshooting". If the information contained there still
fails to remedy the situation then please contact
Anl_GETS_E_710_Kit_SPK7.indb 25 Anl_GETS_E_710_Kit_SPK7.indb 25
GB
our service department or another similarly qua-
lifi ed workshop. Important! Do not actually touch
the surface with the tip of the cutter rail when per-
forming this test. Keep a safe distance (approx.
20 cm).

8.3 Sharpening the saw chain

Eff ective working with the chainsaw is only pos-
sible if the saw chain is in good condition and
sharp. This also reduces the risk of kickback. The
saw chain can be re-sharpened by any dealer.
Do not attempt to sharpen the saw chain yourself
unless you have the necessary special tools and
experience.

9. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
10. Cleaning, storage and ordering
of spare parts
Carry out the cleaning and maintenance work be-
fore putting into storage.
10.1 Cleaning
•
Regularly clean the clamping mechanism by
blowing it out with compressed air or cleaning
it with a brush. Do not use tools for cleaning.
•
Keep the handles free of grease so that you
can maintain a firm grip.
•
Clean the equipment as required with a damp
cloth and, if necessary, mild washing up li-
quid.
Danger!
•
Always disconnect the mains plug before
cleaning the chainsaw.
•
Never immerse the unit in water or other li-
quids in order to clean it.
10.2 Storage
•
If you are not going to use the chainsaw for an
extended period of time, remove the chain oil
from the tank. Briefly immerse the saw chain
and the cutter bar into an oil bath and then
wrap them in oil paper.
•
Store the equipment and its accessories out
- 25 -
21.04.16 14:04 21.04.16 14:04