System Features; Function Descriptions; Fcc Rules And Regulations - Gemini UZ-1128 M Manual Del Operador

INTRODUCTION:
Congratulations on your purchase of a GEMINI wireless system. This
state of the art unit includes all the latest features backed by a three
year limited warranty. Prior to use, we suggest that you carefully read
the instructions.

SYSTEM FEATURES:

• UZ-1128 M includes UZ-1128 diversity receiver & ZM-128 handheld microphone
• UZ-1128 H includes UZ-1128 diversity receiver, HSM-X4 headset mic with mini XLR
& ZB-128 belt pack transmitter with mic/line switch
• UZ-1128 L includes UZ-1128 diversity receiver, LAV-X4 lavalier mic with mini XLR
& ZB-128 belt pack transmitter with mic/line switch
• UZ-9128 M includes UZ-9128 true diversity receiver & ZM-128 handheld microphone
• UZ-9128 H includes UZ-9128 true diversity receiver, HSM-X4 headset mic with mini XLR
& ZB-128 belt pack transmitter with mic/line switch
• UZ-9128 L includes UZ-9128 true diversity receiver, LAV-X4 lavalier mic with mini XLR
& ZB-128 belt pack transmitter with mic/line switch
• Balanced & unbalanced outputs
• 128 band UHF synthesizer controlled frequencies
• Phase locked loop (PLL) circuitry
• Super high sensitivity with extremely low noise transmission & reception
• Stable & quality SMT assembled PCB module
• LCD display screen
• RF & AF LED meters
• Squelch control
• ¼" earphone output for UZ-1128
• ZM-128 has a uni-directional condenser unit microphone
• HSM-X4 has an electret condenser unit microphone
• LAV-X4 has an electret condenser unit microphone
• ZM-128 has a rechargeable input for battery recharging
CAUTIONS:
1. In the UK Some wireless microphone systems require a license. This
depends on the frequency of the system and the country in which it is
to be used. It is the responsibility of the user to establish if a license is
required. As a guide, for the UK and Europe, VHF radio microphones
between 173.800 and 175.000 MHz, or UHF microphones between 863
MHz and 865 MHz do not need a license. This is for microphones work
ing at normal power (10mW ERP hand-held or 50mW ERP if body
worn). All other use on alternative frequencies needs a license. More
information on this can be found at
default.aspx If in any doubt, users are advised to investigate the
licensing requirements for their region.
2. All operating instructions should be read before using this equipment.
3. To reduce the risk of electrical shock, do not open the unit. THERE ARE
NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a
qualified service technician.
4. Do not expose this unit to direct sunlight or to a heat source such as a
radiator or stove.
5. Dust, dirt and debris can interfere with the performance of this unit. Make
an effort to keep the unit away from dusty, dirty environments, and cover
the unit when it is not in use. Dust it regularly with a soft, clean brush.
6. When moving this equipment, it should be placed in its original carton
and packaging. This will reduce the risk of damage during transit.
7. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
8. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY
CONTROLS OR SWITCHES.
9. REMEMBER, ANY CHANGES MADE TO THE UNIT WITHOUT
AUTHORIZATION FROM GEMINI WILL VOID YOUR WARRANTY.

FCC RULES AND REGULATIONS:

This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1)This device may not cause harmful
interference and (2) This device must accept any interference received,
including interference that may cause undesired operation
NOTICE: THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE
THE EQUIPMENT.
IMPORTANT NOTE, TO COMPLY WITH THE FCC RF EXPOSURE COMPLIANCE REQUIREMENTS, NO
CHANGE TO THE ANTENNA OR THE DEVICE IS PERMITTED. ANY CHANGE TO THE ANTENNA
OR THE DEVICE COULD RESULT IN THE DEVICE EXCEEDING THE RF EXPOSURE
REQUIREMENTS AND VOID USER'S AUTHORITY TO OPERATE THE DEVICE.
UZ-1128 WIRELESS SYSTEM:
The UZ-1128 & UZ-9128 wireless systems are high quality audio products
that provide excellent performance under most operating conditions.
receivers are used with our 700 selectable channels transmitters.
receiver operates in UHF band frequency with PLL synthesized control.
Powered by 12V DC. Operating in UHF band frequency with synthesizer
controlled. The wireless microphone system with 700 selectable
frequencies via Phase Locked Loop (PLL) circuitry makes it easy to choose
non-interfered channels. Super high sensitivity, extremely low noise
transmission and reception. Diversity technology ensures the reception
quality.
WIRELESS NOTES:
:www.jfmg.co.uk/jfmgecom/
The
• Before setting up, make sure that the transmitter and receiver are tuned
to the same frequency.
• Do not use two transmitters in the same frequency. Use good quality
batteries to avoid the damage resulting from a defective leaking battery.
• Turn the volume control on the receiver to adjust receiver output level to
match input level requirements of an audio mixer or amplifier.
• While checking sound, move the transmitter around the area where you
use the system to look for dead spots. If you find any dead spot, change
the receiver position. If it does not work, avoid such places.
• To avoid interference, do not put the receiver too near metal object and
avoid obstructions between transmitter and receiver.
• Avoid the interference from TV, radio, other wireless appliances and etc.

FUNCTION DESCRIPTIONS:

UZ-1128 & UZ-9128 RECEIVERS:
HEADPHONE MONITOR VOLUME CONTROL: Rotate this knob to
(1)
control headphone volume level.
HEADPHONE INPUT CONNECTOR: Plug headphone into this 1/4" jack
(2)
connector to monitor receiver audio.
NOTE: NUMBERS (3)-(11) APPLY TO BOTH UZ-1128 & UZ-9128 RECIEVERS.
POWER: Pushes the receiver on and off.
(3)
CHANNEL + BUTTON: Press this button to change channel forward.
(4)
CHANNEL - BUTTON: Press this button to change channel backward.
(5)
PROGRAMMABLE DISPLAY: Displays channel number, frequency and
(6)
volume level.
RF LEVEL INDICATORS: Five LEDs per RF antenna channel glow to
(7)
indicate RF signal strength. The more LEDs that glow, the stronger the
received signal. If none of these LEDs glow, no signal is being received.
AF LEVEL INDICATORS: Five LEDs glow to indicate audio signal
(8)
strength. Green indicates normal operation. RED indicates approaching
overload condition.
VOLUME + BUTTON: Press this button to increase the receiver output
(9)
level to match the input sensitivity of an audio mixer or an amplifier.
VOLUME - BUTTON: Press this button to decrease the receiver output
(10)
level to match the input sensitivity of an audio mixer or an amplifier.
DC OUT: Connect the supplied cable to the receiver and the microphone,
(11)
and it takes around 10 hours to charge.
ANTENNA INPUT CONNECTOR: TNC-type connectors provide
(12)
connection to the supplied antennas or to coaxial cable used with an
antenna divider, antenna boosters or remote antennas.
(13) ANTENNA: Fixed-length UHF antenna permanently mounted on rear panel.
NOTE: NUMBERS (14)-(17) APPLY TO BOTH UZ-1128 & UZ-9128 RECIEVERS.
(14) BALANCED OUTPUT: 3-pin XLR connector provides balanced low-
impedance output
(15) UNBALANCED OUTPUT: 1/4" phone jack provides unbalanced low-
impedance output
(16) SQUELCH: The squelch adjusts the output level to suppress the noise.
The higher squelch control, the lower the sensitivity of the receiver and
decrease the service area of the system. Set the squelch to minimum
before turning the receiver on.
(17) DC IN: Input connector for the supplied AC adapter.
To combine two receivers in a 19" standard rack by using 2 short L type plastic
racks (L2) and 2 metal connecting plates (C1).
The
(4) (4) (4)
(4) (4)