Sunbeam 3964-099 Manual De Instrucciones página 4

WARNING: The patented MOTION SMART
recommended means for turning your iron off. See "Caring for Your Iron After
Use" for information on turning off your iron and storing it safely between use.
C Y
ARING FOR
T O Y I
URNING FF OUR RON
1.Turn the Steam Lever to O /Off (Dry) and Fabric Select Slide to Off.
2.Unplug the iron from the power source.
WARNING: NEVER yank the power cord when unplugging the iron.
This can damage the cord.
S Y I
TORING OUR RON
1.Allow the iron to cool.
2.If you do not use your iron on a daily basis, empty the water reservoir after
each use for a longer iron life. To do so, unplug the iron, turn the iron upside
down, open the fill hole cover, and allow water to flow from the fill hole.
Shake the iron gently to remove trapped water drops.
3.Loosely loop the power cord around the heel rest and store the iron on its
heel rest.
I : Wrapping the cord around the iron too tightly can damage the cord.
MPORTANT
T : When not ironing, always set the Steam Lever to O/Off (Dry) and the Fabric
IP
Select Slide to Off.
M
AINTAINING
C S
LEANING THE OLEPLATE
Clean the soleplate if starch or other residue accumulate.
To clean the Soleplate:
1.Allow the iron to cool and then wipe it with a soft, damp cloth.
WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean
the soleplate. This will damage the finish.
2.Run the iron over an all-cotton cloth to remove any residue.
U S -C
SING THE ELF LEANING
You should use the Self-Cleaning feature once a month to maintain the optimal
performance of your iron.
To use the Self-Cleaning feature:
1. Move the Steam Lever back and forth from
debris and minerals from the Steam Valve. This keeps water flowing into the steam
chamber.
2.Fill the water reservoir with tap water to the MAX line.
3.Set the Fabric Select Slide to LINEN.
4.Plug the iron into a power outlet and allow the iron to heat for 2 minutes.
5.Turn the Fabric Select Slide to MIN and unplug the iron.
6.Hold the iron over a sink in a horizontal position.
®
Auto-Off is a safety feature, not a
I A
OUR RON FTER
Y C I
OUR LASSIC RON
F
EATURE
O /Off (Dry) several times to remove
6
WARNING: Be careful not to touch the iron's hot surfaces.
7.Press the self-clean button and hold. Water will begin dripping from the steam
vents. To make sure that all of the water is removed from the tank, slowly
U rock the iron side to side and front to back for 30 seconds. When rocking
SE
the iron, dip the nose of the iron slightly below the rear of the iron to make
certain the water circulates completely. Release self-clean button after
one minute.
8.Turn the iron upside down and allow the remaining water to flow out of
the fill hole.
9.Dry the soleplate with a towel.
10. Plug in the iron and set the Fabric Select Slide to Linen. Let the iron heat
for 2 minutes to dry out the iron completely.
11. Set the Fabric Select Slide to MIN, unplug the iron and allow it to cool.
• Always read garment labels and follow the manufacturer's ironing instructions.
• Sort the articles to be ironed according to the type of fabric.
• You should first iron garments requiring low temperature (e.g., silks and
synthetics) to avoid damaging them with an iron that is too hot.
• If you are unsure of the fabric content of the garment, test a small area,
such as a seam or facing, before ironing a visible area. Start with a low
temperature and gradually increase the heat to find the best setting.
• When changing the temperature from a high setting to a low setting,
allow approximately 5 minutes for the lower temperature to be reached.
• When steam ironing, use long, slow passes over the fabric. This will allow
the steam to penetrate the fabric while allowing the heat of the soleplate
to dry out the moisture.
• To iron linens, turn garment inside out. Be careful not to use an iron
that is too hot because the lining may melt or stick to the soleplate.
• To iron zippers, use an ironing cloth or make sure the zipper is closed
and iron over the flap. Never iron directly over an unprotected zipper.
• Use the Ironing Guide (on Page 8) to select the best setting and method for the
fabric you plan to iron.
I T
RONING IPS
7