Instructions For Use; Placement Tool; Assembly; Electrical Connection - stayer EPG300 Manual De Instrucciones

and injects toxins into the body.
Exercise caution when cleaning and changing
Ÿ
nozzle inserts. If the nozzle insert should become
clogged during spraying, follow the manufacturer's
instructions for switching off the system and
relieving the pressure before removing the nozzle.
Fluids under high pressure can penetrate the skin, inject
toxins into the body and lead to serious injury.
Keep the plug of the mains cord and the trigger
Ÿ
switch of the spray gun clear of paint and other
fluids. Never hold the cord by its connectors to
support it. Failure to follow the instruction can lead to
electric shock.

3. Instructions for use

3.1 Placement Tool

Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
To get started, place the machines in a clean and stable,
begin by preparing the material to be sprayed, taking into
account this point, because if not well prepared to hand the
material, the machine will not work in conditions optimal.
3.2 Assembly (Fig.1)
Before any work on the machine itself, pull the mains
plug.
Mounting the Spray Gun and the Electrical Unit.
Connecting the Electrical Unit with the Spray
Gun.(EPG300)
- Insert the spray gun 9 onto the electrical unit 1 until it can
be heard to engage.
- It should be noted that SD 4 moths found on the sides of
the gun should be positioned
position ___ moths and make sure that the spray gun is
secure.
Removing the Electrical Unit
– Turn the two red SDS release buttons 4
spray gun 9 out of the electrical unit.
1-MOUNT (EPG700)
-Connect one end of the air hose 23:
-One end of the device to paint 24 by turning in
counterclockwise to clockwise.
-The other end of the air hose (23) connected to the air
outlet 26 of the trolley 25 to secure the hose to turn it
counterclockwise to clockwise.
Warning: Any position of the hose 23 can be chosen to
connect both the spray gun, as in the trolley Note, the
arrows drawn on the edges of the hose 23, to connect
properly.
To remove the air hose 23, turn knob clockwise until
placed in the position of the indicator arrow and pull
ENGLISH
14
___ . Then return to the
and pull the
14
the hose to remove.
When the device is turned on the air continuously flow
from the air cap.

3.3 Electrical connection

– Plug the mains plug into a socket outlet.
– Grasp the power tool and point it at the spray surface.
The power tool is equipped with a two-step trigger switch
16. The first step starts the turbine.
The second step transports the spraying material.
– Pull the trigger switch 16 until spraying material starts to
come out.
Switching Off – Release the trigger switch 16.
– Pull the mains plug from the socket outlet.

3.4 Illustrated description

The fan motor causes a flow of air flowing through the
air hose 23 to the spray gun. The air flow is atomized
coating material on the nozzle 20 and pressurized
vessel 11. This pressure forces the coating material
through the riser pipe to the nozzle 20. The
adjustment of air and pressure can be adjusted
progressively. (Fig. 4-5-6).
1 Electrical unit
2 Cable clamp
3 Air filter cover
4 SDS release button*
5 Mains cable
6 Base/foot*
7 Hooks for air-filter cover
8 Air filter
9 Spray gun
10 Suction tube with container seal
11 Container for spray material, 800 ml
12 Vent cover
13 Diffuser
14 Clamp nut
15 Thumbwheel for spraying capacity
16 Trigger switch
17 Air outlet
18 Venting valve*
19 Membrane*
20 Nozzle*
21 Nozzle seal*
22 Measuring cup
23 Air Hose*
24 Air intake
25 Troley*
26 Out of air
27 Cleaning needle*
* The accessories illustrated or described are not attached
to the material standard. The full range of accessories can
be found in our accessories program.

4. Operating instructions

Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine.Power tools marked with
230 V can also be operated with 220 V.
Pay attention that the power tool cannot draw in dust or
other contamination during operation.