Maintenance And Service - Bosch GAS 35 L SFC+ Professional Manual Original

22 | English
– Deactivating SFC+
Push the SFC+ switch (18) forwards (position 0).
– Activating SFC+
Push the SFC+ switch (18) backwards (position I).

Maintenance and service

Maintenance and cleaning
Pull the plug out of the socket before cleaning or per-
u
forming maintenance on the vacuum cleaner, making
tool adjustments, changing accessories or putting
away the vacuum cleaner. This safety measure prevents
the vacuum cleaner from being started accidentally.
To ensure safe and efficient operation, always keep
u
the dust extractor and the ventilation slots clean.
Wear a dust mask when servicing and cleaning the va-
u
cuum cleaner.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
For the user to carry out maintenance, the vacuum cleaner
needs to be disassembled, cleaned and maintained as far as
this is possible without endangering maintenance personnel
or other persons. Before disassembly, the vacuum cleaner
should be cleaned to prevent any potential hazards. The
room in which the vacuum cleaner is disassembled should
be well ventilated. Wear personal protective equipment
while carrying out maintenance. After completing mainten-
ance, the maintenance area should be cleaned.
An inspection regarding the dust extraction capability must
be carried out at least once a year by the manufacturer or
someone who has been trained, e.g. to check for filter dam-
age, that the vacuum cleaner is tight and that the control unit
is functioning correctly.
Class L vacuum cleaners which were located in dirty environ-
ments should have their exteriors, as well as all their com-
ponents, cleaned or treated with sealant. When performing
maintenance and repair work, all dirty parts that cannot be
cleaned satisfactorily must be disposed of. Such parts must
be disposed of in impermeable bags in accordance with the
valid provisions for disposing of such waste.
Removing/changing the flat-pleated filter (see figures
J1–J2)
Suction power is dependent on the condition of the filter.
Therefore, the filter should be cleaned regularly.
If the flat-pleated filter (24) becomes damaged, replace it
immediately.
– Pull on the closing flap (14) and open the filter cover
(34).
– Hold the flat-pleated filter (24) by the supports and take
it out from above.
– Use a damp cloth to remove any dust and dirt that ac-
crues around the closing edge of the filter cover (34)
1 609 92A 4LX | (16.11.2018)
when removing the flat-pleated filter (24).
PES and PTFE flat-pleated filters can be rinsed out under
running water.
– Insert the cleaned (or a new) flat-pleated filter (24), en-
suring that it is positioned correctly and securely.
– Close the filter cover (34) again (must audibly click into
place).
Cleaning the container
– Wipe the container (1) from time to time using a non-ab-
rasive off-the-shelf cleaning product and leave it to dry.
Cleaning the fill level sensors (see figure K)
Make sure that the fill level sensors are cleaned (35) occa-
sionally.
– Open the catches (9) and remove the top part of the dust
extractor (8).
– Clean the fill level sensors (35) using a soft cloth.
– Put the top part of the vacuum cleaner (8) on and close
the catches (9).
Accessories
Paper filter bag (dry)
Fleece filter bag (dry)
Wet filter bag (wet)
Disposal bag (PE) (dry/wet)
Storage and transport (see figure L)
– Wrap the power cable around the cable holder (13).
– Insert the accessory into the holders provided for it: Suc-
tion tubes (29) into the holders (15), crevice nozzle (25)
into the holder (16), floor nozzle (28) into the holder
(17).
– Open the elastic bands of the vacuum hose holder (4)
and wrap the vacuum hose (21) around the top part of
the dust extractor in the holder (4).
Hook the elastic bands back in.
– Click the L-Boxx on to the adapters (7).
– Before transporting the dust extractor, remove any full
disposal bags/dust bags and empty any liquids that have
been absorbed, in order to avoid placing unnecessary
strain on the back and prevent injury.
Only ever carry the dust extractor by the carrying handle
(6).
– Store the dust extractor in a dry room and secure it so
that it cannot be used by unauthorised persons.
– Put the castor brake (11) down to hold the castors (12)
in place.
Rectifying faults
If a fault (e.g. a filter damage) occurs, the vacuum
u
cleaner must be switched off immediately. The fault
must be repaired before resuming operation.
Accessory number
2 607 432 035
2 607 432 037
2 607 432 039
2 607 432 043
Bosch Power Tools