Specific Safety Rules - Makita 5621RD Manual De Instrucciones

Ocultar thumbs Ver también para 5621RD:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 29
ENGLISH
1
A typical illustration of proper
hand support, workpiece sup-
port, and supply cord routing (if
applicable).
2
To avoid kickback, do support
board or panel near the cut.
3
Don't support board or panel
away from the cut.
4
Push button
5
Battery cartridge
6
Loosen (counterclockwise)
7
Hex wrench
8
Shaft lock
SPECIFICATIONS
Model
Blade diameter ................................................... 165 mm
Max. cutting depth
At 90° ................................................................. 54 mm
At 45° ................................................................. 38 mm
-1
No load speed (min
) ............................................. 2,600
Overall length ..................................................... 364 mm
Net weight .............................................................. 3.8 kg
Rated voltage ....................................................D.C.18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
Explanation of general view
9
Bolt
10 Outer flange
11 Saw blade
12 Inner flange
13 Hex socket head bolt
14 Cutting depth
15 Lever
16 Bevel scale plate
17 Clamp screw
18 Adjusting screw
19 Base
20 Triangular rule
21 For straight cuts
5621RD
7.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
ENC004-1

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to circular saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
Danger:
1.
2.
22 Cutting line
23 For 45° bevel cuts
24 Switch trigger
25 Lock-off button
26 Clamp screw
27 Rip fence (Guide rule)
28 Dust nozzle
29 Screws
30 Hose 28 mm in inner dia.
31 Vacuum cleaner
32 Limit mark
33 Brush holder cap
34 Screwdriver
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Keep hands away from cutting area and the
blade. Keep your second hand on auxiliary han-
dle, or motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece. Do not attempt to remove cut material
when blade is moving.
CAUTION: Blades coast after turn off. Wait until
blade stops before grasping cut material.
GEB029-1
5

Publicidad

Tabla de contenido
loading

Tabla de contenido