Specific Safety Rules - Makita JR3000 Manual De Instrucciones

ENGLISH
1 Hex wrench
2 Bolt
3 Shoe
4 Bolt
5 Speed change switch
SPECIFICATIONS
Model
Length of stroke ........................................................................... 30 mm
Strokes per minute ...................................................................... Hi : 2,500
Overall length .............................................................................. 400 mm
Net weight .................................................................................... 2.9 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adher-
ence to recipro saw safety rules. If you use this
tool unsafely or incorrectly, you can suffer seri-
ous personal injury.
1. Hold power tools by insulated gripping sur-
faces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord.
Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock the
operator.
2. Use clamps or another practical way to
secure and support the workpiece to a stable
platform.
Holding the work by hand or against your
body leaves it unstable and may lead to loss of con-
trol.
3. Always use safety glasses or goggles. Ordi-
nary eye or sun glasses are NOT safety
glasses.
4. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond the
workpiece before cutting so that the blade
will not strike the floor, workbench, etc.
7. Hold the tool firmly.
8. Make sure the blade is not contacting the
workpiece before the switch is turned on.
Explanation of general view
6 Switch trigger
7 Lock button/Lock-off button
8 Speed control screw
9 High
10 Low
9.
10. Do not leave the tool running. Operate the
11. Always switch off and wait for the blade to
12. Do not touch the blade or the workpiece
13. Do not operate the tool at no-load unneces-
14. Always use the correct dust mask/respirator
15. Some material contains chemicals which may
GEB008-2
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
OPERATING INSTRUCTIONS
Installing saw blade (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
First, use the hex wrench to loosen the bolt. With the
blade teeth facing upward or downward, insert the blade
until the hole in the blade shank is just over the protru-
sion on the slider. Then tighten the bolt to secure the
blade.
Adjusting shoe (Fig. 2)
Loosen the two bolts holding the shoe. Then slide the
shoe back or forth to the desired position and tighten the
two bolts securely. When the blade loses its cutting effec-
tiveness in one place, reposition the shoe to obtain better
cutting in another.
11 Limit mark
12 Brush holder cap
13 Screwdriver
JR3000
Low : 1,900
Keep hands away from moving parts.
tool only when hand-held.
come to a complete stop before removing the
blade from the workpiece.
immediately after operation; they may be
extremely hot and could burn your skin.
sarily.
for the material and application you are work-
ing with.
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material sup-
plier safety data.
JR3000V
30 mm
0 – 2,300
400 mm
2.9 kg
3