Technical Data; Troubleshooting - Vivanco FMS 2000 Instrucciones De Uso

GB
fitted with a jack socket, you can use the LINE-OUT or AUX-OUT of your audio source
using the audio lead. To do so, connect the phono plugs of the Y-audio lead to the phono
output sockets of your audio source and connect the 3.5 mm jack socket to the audio lead
of the transmitter. Please observe the correct polarity (red to red and white to white)
when connecting the phono plugs.
Note: The transmitter has automatic input signal adjustment so that overmodulation of the
transmitter by excessive input signals is avoided. This means that you can use both
adjustable and non-adjustable jack sockets.
4. Now switch on your audio source (TV, hi-fi system, etc.), making sure that it is
emitting an audio signal.
5. The transmitter now switches itself on automatically. The power-on lamp (A1) comes on.
6. If your audio source emits only a mono signal, set the Mono / Stereo switch (A3) on
the transmitter to the Mono position. For stereo signal, set it to the Stereo position.
Note: The transmitter automatically switches itself off when it does not receive an audio signal
for a longer period.
When audio transmission is resumed, the transmitter automatically switches itself on again.
4.2 Active speaker as receiver
1. Power supply with AC adapter (D)
Connect the power supply lead of the AC adapter to the socket provided (B11) on the
active speaker. Then plug the AC adapter into a mains socket (230V/50 Hz).
2. Power supply with batteries/battery packs (not supplied with the set)
Insert 6 AA batteries in the battery compartment (B12) on the back of the active
speaker, ensuring correct polarity (see illustration). Then close the battery compartment.
3. Switch on the audio source connected to the transmitter.
4. Now switch the On/Off switch (B8) to the "ON" position in both mains and battery
operation. The power-on lamp (B7) lights up red.
5. Set the volume control (B8) to the required level.
6. Start the transmission scan using the Auto Tuning button (B10). After a short time,
reception begins automatically. Should there be interference from other appliances or
any other source, select a different frequency on the transmitter (channel selection
switch A4) and restart the transmission scan. After correct adjustment you will now
receive the audio signals without any distortion or noise.
7. After use, switch the On/Off (B8) switch to "OFF".
8. If required, you can amplify the bass sound by pressing the Bass Boost switch (B9).
Note: In battery operation, you should now be able to move from room to room with the active
speakers without any reception interference. If the signal is interrupted or distorted,
restart the scan.
When receiving over long distances, the signal becomes gradually weaker. This is
indicated by an increase in background noise and the sound signal becoming almost
inaudible. Should there be interference from other appliances or any other sources, select
a different frequency (A4) on the transmitter and repeat steps 6.
5 Trouble-shooting
Problem
No sound
10
Solution
Make sure that the On/Off switch (B8) on the left at the front
is in the "ON" position.
Are the power-on lamps on the transmitter (A1) and the
speaker (B7) constantly lit?
GB
Sound interference
If these suggested solutions do not lead to the desired result, please contact your dealer.
Note: This appliance is not authorised for any application other than those mentioned above. No
liability is accepted for any problems arising, damage caused, etc. if used otherwise. In
addition, the connection leads (e.g. audio leads) used should not be longer than 3 metres.
Naturally, Vivanco gives its warranty for all appliances in accordance with legal warranty
stipulations.
6

Technical data

Amplifier output:
Transmission frequency:
Frequency range:
Signal-to-noise ratio:
Non-linear distortion factor: < 1.5 %
Power supply:
Subject to alteration without notice.
20012004
Otherwise check whether the AC adapters (C and D) are
correctly connected and check the condition of the
batteries/battery packs.
Details in sections 4 and 5.
Check whether the audio source is switched on and emitting
a signal.
Have you connected the transmitter to the audio source?
If you are operating via an adjustable headphones socket on
your audio source, make sure that it is turned up high
enough (e.g. to about the middle setting).
Check the volume control on the active speaker.
Change to a different transmission frequency using the
frequency selector switch (A4).
Readjust the receiver. (B10)
Make sure that the interference is not being caused by your
audio source.
In certain cases it may be necessary to alter the position of
the transmitter horizontally and/or vertically.
Check that the power-on lamp (B7) is lit.
2 Watts (RMS) per channel
863 - 864 MHz
65 - 12,000 Hz
> 50 dB
Transmitter: AC adapter, 230V/50Hz AC,
12Volt/150mA DC
Active speaker: AC adapters, 230V/50Hz AC,
12Volt/550mA DC
11