Safety Checks; General Check - Alpina B 26 J Manual De Instrucciones

3. Fill with fuel before using the machine. For
preparing the mixture, refuelling methods
and precautions (see paragraph 7.2, 7.3).
4. wear the harness correctly
(see paragraph 6.1.1).
6.1.1 Using harnesses
The belts must be adjusted to suit
the operator's height and build.
Always use a harness that is suited
to the weight of the machine:
– for machines weighing less than 7.5 kg,
single or double belt models can be used;
– the double belt model must be used for
machines weighing more than 7.5 kg.
• Models with single belt
The harness must be put on before connecting
the machine to the special coupling.
The belt (Fig. 19.A) must go from the
left shoulder to the right hip.
The belt must be worn with:
– the machine's support (Fig. 19.A.1),
the snap-hook (Fig. 19.A.2) and
the quick release (Fig. 19.A.3)
coupling on the right side;
• Models with double belt
The harness must be put on before connecting
the machine to the special coupling.
The belt (Fig. 19.B) must be worn with:
– the machine's support (Fig. 19.B.1),
the snap-hook (Fig. 19.B.2) and
the quick release (Fig. 19.B.3)
coupling on the right side;
– the quick release in front (Fig. 19.B.3);
– the belts cross-over on the
operator's back (Fig. 19.B.4);
– the buckles properly fastened (Fig. 19.B.5).
The belts must be tensioned so that the load
is evenly distributed on the shoulders.
• Models with back-pack harness
Harness with back-pack must be
worn after starting the machine.
The harness (Fig. 19.C) must be worn with:
– the harness straps on the operator's
shoulders (Fig. 19.C.1);
– the buckles properly fastened (Fig. 19.C.2).
– the snap-hook coupling on the
right side (Fig. 19.C.3);
– the quick release in front (Fig. 19.C.4).
The belts must be tensioned so that the load
is evenly distributed on the shoulders.

6.2 SAFETY CHECKS

Run the following safety checks and
check that the results correspond to
those outlined on the tables.
Always carry out the
safety checks before use.

6.2.1 General check

Object
Handles (Fig. 1.F;
Fig. 1.G , Fig. 1.I)
Cutting means
guard. (Fig. 1.E)
Connection point of
the harness (Fig. 1.J)
Quick release (Fig. 19.A.3;
19.B.3, Fig. 19.C.4)
Screws on the machine
and on the cutting means
Cutting means (Fig. 1.D.1;
Fig. 1.D.2, Fig. 1.D.3)
Metal blade (if fitted)
(Fig. 1.D.2, Fig. 1.D.3)
Air filter (Fig. 29.C,
Fig. 30.C, Fig. 31.C)
Electric cables and
spark plug cable
Spark plug cap
(Fig. 18.H;)
6.2.2 Machine operating test
Action
Start the machine
(par. 6.3)
Push the throttle control
lever (Fig. 18.B) and the
throttle safety lever at the
same time (Fig. 18.C).
EN - 10
Result
Clean, dry and fixed
firmly to the machine.
Suitable for the cutting
means used, fixed
correctly and firmly to
the machine, not worn/
deteriorated or damaged.
Correctly positioned.
Efficient. Must enable
the machine to be
freed rapidly in the
event of danger.
Correctly tightened
(not loose)
Not damaged or worn.
Sharp
Clean
Undamaged to
prevent sparks.
Undamaged and fitted
correctly on the spark plug
Result
The cutting means
(Fig. 1.D.1, Fig. 1.D.2,
Fig. 1.D.3) must not
move when the engine
is running idle.
The levers must move
freely and not be forced.