Tuner Controls; Band Buttons; Tuning Buttons; Memory Button - Rotel RSX-1562 Manual De Instrucciones

English
To change a setting, place the highlight on the desired line using the
Up/Down buttons and use the Left/Right buttons to increase or decrease
the delay. To return to the MAIN menu, press the ENT button. Press the
RCVR/SETUP button on the remote to cancel the display and return to
normal operation.

Tuner Controls

This Rotel receiver features a digital synthesized AM/FM tuner with
RDS capability and 30 station presets. The unit offers a wide range of
tuning options. Here is an overview of tuning options.
• Manual frequency tuning
frequency (when in frequency tuning mode). Press and release a
TUNING button (CH +/-
lets you enter the desired station frequency
• Direct frequency tuning
digits. Press the DIRECT button (or FRQ-D button
and enter the digits using the NUMERIC buttons
• Automatic frequency search tuning
the next receivable broadcast signal. Press and hold a TUNING
L
button (CH +/- on the remote) for at lease one second to search
up or down.
lets you directly enter the number of a memorized
• Station preset tuning
station preset. Enter the number of the memorized preset using the
NUMERIC buttons.
jumps up/down to the next memorized station preset.
• Preset tuning
When in PRESET mode, press a TUNING button (CH +/-
remote) to select the next station preset.
D on the remote to toggle between preset and frequency tuning
modes.
• RDS (Europe) or RBDS (USA) tuning
tuning and search features based on data codes encoded with the
broadcast signal. See the RDS section of this manual for detailed
information.
Note: The receiver comes configured for tuning in the market where
you purchased it. (N. America or Europe). To change this default
setting, see the information on the DEFAULT SETUP on-screen menu
later in this manual.

BAND Buttons

4K
Press the BAND button to toggle between AM and FM reception.
An indicator in the front-panel display confirms your choice and the
currently tuned station frequency is shown.

TUNING Buttons

0L
The TUNING buttons (CH +/-
different tuning functions, depending on the mode of operation.
In the normal FREQUENCY tuning mode, press a TUNING button
(CH+/- L on the remote) and release to manually jump to the
next station frequency, regardless of whether or not a station is
broadcasting on that frequency. For auto frequency search tuning,
press and hold the TUNING button for approximately one second. An
AUTO indicator will appear in the front-panel display and the tuner
tunes up or down to the next station
L
on the remote) to tune.
H on the remote)
8G
searches up or down to find
Press the P-TUN button
provides a range of special
L on the remote control) provide three
will begin scanning up or down through the frequencies until the next
available signal is detected. If this is not the desired station, repeat
the automatic tuning procedure to find the next station. Weak stations
will be skipped during auto tuning.
In the PRESET tuning mode, press a TUNING button (CH +/-
the remote) and release to jump to the next memorized station preset.
Note: Toggle between FREQUENCY and PRESET tuning by pressing
the P-TUN button
In the RDS PTY search mode, press a TUNING button (CH +/-
remote) to select the desired program type from the scrolling list in the
display. See the section on RDS tuning for more details.

MEMORY Button

The MEMORY button (labeled MEM on the remote) is used with the
NUMERIC buttons to store memorized station presets. See the next
section for detailed instructions.
.

NUMERIC Buttons : Station Presets

The receiver can store up to 30 station presets for recall at any time
using the NUMERIC buttons on the front panel. To memorize a
station:
1. Tune to the desired station, AM or FM.
2. Press the MEMORY button (MEM on remote). A MEMORY
indicator will flash for five seconds in the front-panel display.
3. While the MEMORY indicator is flashing, press the number of the
L on the preset where you wish to store the station frequency. For example,
to memorize the station as preset 3, press the 3 button. To memorize
preset 15, press the 1 button followed by the 5 button.
4. A previously stored frequency is erased from memory when a new
frequency is memorized for the same preset number.
To tune to a previously memorized station, just press the preset number
on the NUMERIC buttons. For example, to tune to preset 3, press the
3 button. To tune to preset 15, press the 1 button and then press the
5 button.
Note: If the TUNER is not already the selected input, pressing a
NUMERIC button on the front-panel activates the TUNER. If using the
NUMERIC buttons on the remote, first manually select the tuner input
(press TUN button
The NUMERIC buttons can also be used for direct access tuning (see
next section)

DIRECT Button

FRQ-D Button ("10+" key)

If you know the frequency of the desired station, you may tune it
directly using the DIRECT button and the NUMERIC buttons.
1. Press the DIRECT button on the front panel or the FRQ-D button
on the remote to change the NUMERIC buttons from station preset to
Direct Access mode. The station frequency in the front panel display
will change to a series of four bars, representing the digits of a station
frequency, with the first bar flashing.
D
on the remote.
=H
=8HG
M
), if not already activated.
9
H
43
L on
L
on