Zone 2-4 Setup; Volume Setup; Default Setup - Rotel RSX-1562 Manual De Instrucciones

46
1562. This allows the audio from the TV to be played through your
hometheater system.
Note: When ARC is enabled, the Rotel unit will play the audio from
the TV. The volume can be controlled by the TV's remote control.
Note: When HDMI control is ON, the unit will pass HDMI Video and
Audio signals in Standby mode direct to the TV. The Rotel unit do not
have to be powered on if you only want to use the speakers of the TV
for audio. But the Rotel unit must be set to the correct input prior to
standby.
POWER CONTROL: Options are Yes, No.
other HDMI enabled units in your system to turn the RSX-1562 on or
off. In normal operation, powering ON the source will also turn on the
RSX-1562 and the TV. Turning the TV off, will turn off the RSX-1562
and the source.
Note: For power control to operate, all components in the system must
have power control enabled from source to displays. Although the unit
has been tested with most major brands of displays and sources, there
may still be occasional compatibility problems.

Zone 2-4 Setup

Z O N E S E T U P
S O U R C E : C D
V I D E O I N P U T : C o m p o s i t e 1
1 2 V T R I G G E R : 1 _ 3 _ _ _
V O L U M E S E T U P : V a r i a b l e
V O L U M E : 6 0
T U R N O N V O L : L a s t
M A X V O L : M a x
M A I N M E N U
The ZONE SETUP menu provides settings and configuration options related
to the operation of the remote zones. This menu is reached by highlighting
the ZONE line on the MAIN menu and pressing ENT.
ZONE: Specifies the zone to configure, ZONE 2, 3, or 4. Each zone
is configured individually.
SOURCE: Specifies a source for listening in the selected zone. Options
are CD, TUNER, VIDEO 1-6, SOURCE, and OFF. Selecting the SOURCE
option links the zone source to the source selected for the main zone
so that the remote zone will hear the same source as the main zone.
Selecting the OFF option turns the zone off.
VIDEO INPUT: Specifies a video source (Composite Video only) for the
selected zone. The options available are Composite 1, 2 and OFF.
VOLUME SETUP: Configures the remote zone outputs for VARIABLE or
FIXED volume levels. VARIABLE allows control of the volume settings in the
remote zone from the RSX-1562's front panel or from a remote control/IR
repeater in the zone. FIXED output disables the volume control. In this
mode, the remote zone level can be fixed at the level specified on the
next line, thus optimizing system performance when sending a fixed level
signal to a preamp or amplifier with its own volume adjustment.
VOLUME: In VARIABLE output mode, this line shows the current volume
setting for remote zone. In FIXED output mode, this volume setting
establishes a permanent fixed output level for the remote zone
Selecting Yes, allows
Z O N E : Z O N E 2
RSX-1562 SURROUND SOUND RECEIVER
TURN ON VOL: Specifies a default volume level to be used each time the
remote zone is activated. You can select LAST to have the zone activate
with the last previously used volume setting. Or, you specify a volume
from MIN (full mute) to MAX, in 1dB increments. Note that this setting
can not exceed the MAX VOL established in the next line of the menu.
MAX VOL: Specifies the maximum volume level for the remote zone.
The volume cannot be adjusted above this level. Settings range from
MIN to MAX in 1dB increments.
12V TRIGGER: The RSX-1562 has six 12V trigger outputs (labeled
1–6) that supply a 12V DC signal to turn on Rotel components and other
components as needed. This menu item turns on specific 12V trigger
outputs whenever the indicated zone is activated. The six 12V Trigger
outputs may be assigned to each zone and can send a turn-on signal
to remote components whenever the remote zones are activated. For
example, ZONE 2 could use 12V Triggers 1, 3 and 6; ZONE 3, 12V
Triggers 2 and 3; ZONE 4, 12V Triggers 5 and 6.
1. Press the Left/Right buttons on the remote to change the first position
from blank to 1 (activating TRIGGER 1 for that zone).
2. Press the ENT button on the remote to move to the next position.
3. Repeat until all six positions are set as desired. A final press of the
ENT button confirms the selection.

Default Setup

D E F A U L T
t T U N E R S E T T I N G : E U R O P E
R E D I R E C T : N o
F A C T O R Y D E F A U L T : N o
U S E R D E F A U L T : N o
S E T U S E R D E F A U L T : N o
S E T N E W P A S S W O R D : N o
M A I N M E N U
The DEFAULT SETUP menu provides access to six functions:
• Set the tuning function for Nor th America or European
frequencies.
• Redirect the Front channel amplifiers or the Center Back channel
amplifiers to power remote speakers in Zone 2, 3 or 4, or redirect
the Center Back channel amplifiers to "Front" for bi-amping.
• Restore all features and settings to the original FACTORY DEFAULT
settings.
• Memorize a custom group of settings as a USER DEFAULT.
• Activate the memorized USER DEFAULT settings.
• Set a NEW PASSWORD for the memorized USER DEFAULT
settings.
To change the TUNER setting: Place the highlight on the TUNER setting
line using the Up/Down buttons and use the Left/Right buttons to change
the setting to N. AMERICA or EUROPE. Then, move the highlight to
the FACTORY DEFAULT line and change the setting to YES, using the
S E T U P
L