Nordcap MARTE Serie Instrucciones De Uso página 17

6 - Electric connection
Important: installation should be made following th
w ith the electric safety regulations in force. Please ref
At the input of the supply it is ne
equal to 3 mm and adequate cutoff power.
Caution: Before connecting the cabinet to the power mains make sure the supply voltage corresponds to the rating on
the serial number plate (consider that the maximum voltage variations admissible are +/- 10%). Make sure the electric
connection is made with cables of a diameter and length capable of withstanding the power and current absorbed by the
display cabinet (TAB. 2 page 4). Cabinets with incorporated compressor are supplied with a cable and plug 2,5 mt long
(FIG. 14 page 4) therefore, it is essential not to exceed this measure in connecting the cabinet to the wall socket. The
cable should be fully extended in a safe position away from possible impact and at a distance from liquids or water and
heat sources. In case of breakage of the power cable of the cabinet, it must be replaced by the manufa
institution in charge of it. The plug should be accessible even after installation of
Im portant: installation should be made following the manufacturer's instructions, by qualified personnel in conformity with
the electric safety regulatio
accident prevention laws, fire prevention regulations, directives).
Always ground the cabinet.
The manufacturer is not liable for any in
If there is no wall socket near where the cabinet is to be installed, pr
in force.
Do not use adapter plugs.
The manufacturer has no liability for any damage to personnel or property caused by improper installation.
7 - Technical features
The cabinet is supplied with a plastic bag containing this manual of instructions that must be kept. It contains technical
data, wiring diagrams and tables concerning the cabinet.
The technical data are also shown on the rating plate (FIG. 15 page 4). It indicates:
1. The trade name of the refrigerated cabinet
2. Code corresponding to the refrigerated cabinet
3. Serial number of the refrigerated cabinet
4 . Supply voltage
5. Supply frequency
6. Maximum power absorbed
7. Maximum power abso
8. Power of standard illumination
9. Usable display area
10. Usable load volume
11. Type of refrigerating gas used in the system
12. Weight of refrigerating gas used to fill each separate system
13. Climatic, environmental and temperature class of reference (dry bulb temperature)
14. Class of refrigerated cabinet depending on the temperature for conservation of the products.
15. Class of safety of ele
16. Number of order against which the refrigerated cabinet was produced
17. Order number relative to production of refrigerated cabinet
18. Year of production of refrigerated cabinet
portant: The rating plate and warning labels should never be removed. The manufacturer is not liable for any damages
Im
caused by failure to respec
This is to certify that the product complies with Legislative Decree no. 108 of 25/01/1992 applying EE
concerning materials and objects expected to come into contact with food produ
8 - Filling with products and use of the cabinet (startup)
With the cabinet off, remove the plastic film protection on the inside and outside and clean the cabinet according to the
instructions in paragraph 11.
After correctly assembling the cabinet (Par. 5) plug it into the mains (as described in Par. 6) and switch the cabinet on,
switch the light on using the switches on the control panel on the rear (FIG. 16 page 4). The gentle hum of the motor and
illumination of the display will indicate that the cabinet is working. The display (FIG. 16 page 4) on the rear casing shows
the working temperature of the display case. The instruction manual for the electronic control to which the display refers is
enclosed with the instruction booklet (tampering with this device is impossibl
specialized expert can intervene on it). The thermostat and gas charge are set in the factory. Tampering with the factory
settings relieves the manufacturer of any liability.
About three hours after switching the cabinet on, you can start filling it with products. Always check that the temperature
reading on the display of the electronic control is suitable for the conservation of the products placed in the display
cabinet.
T he cabinet is designed for the display of food products, which are stored at the temperature of the product, and does not
lowe r it. The product should therefore be placed in the cabinet only after it has been chilled to its proper storage
temperature.
18
cessary to install an omni-polar magnetothermic/differential device with contact opening
ns in force in the country where the cabinet is installed (electric safety regulations and laws,
juries caused by failure to respect this regulation.
rbed during defrosting (where provided)
ctrical system
t this regulation.
e manufacturer's instruction
er to the electrical di agram at page 7.
ovide for connection in conformity with the regulations
s, by qualified personnel only, in conformity
the cabinet.
cts.
e because a password is required and only a
cturer or by
C Directive 89/109