IMER COMBI 250/1000 VA Manual De Uso página 10

Dear Customer,
Congratulations on your choice of purchase: IMER saws are the result
innovations.
To work in complete safety, read the following instructions carefully be-
fore using the machine.
To work in complete safety, read the following instructions carefully be-
fore using the machine.
This OPERATION AND MAINTENANCE manual must be kept on site
by the person in charge, e.g. the SITE FOREMAN, and must always be
available for consultation.
The manual is to be considered integral part of the machine and must
be kept for future reference (EN 12100-2) until the machine is disposed
of. If the manual is damaged or lost, a replacement may be requested
from the manufacturer.
The manual contains important information regarding site preparation,
machine use, maintenance procedures, and requests for spare parts.
Nevertheless, the installer and the operator must both have adequate
experience and knowledge of the machine prior to use.
To guarantee complete safety of the operator, safe operation and long
life of equipment, follow the instructions in this manual carefully, and
observe all safety standards currently in force for the prevention of ac-
cidents at work (use of safety footwear and suitable clothing, helmets,
gloves, goggles etc.).
IMER INTERNATIONAL declines all responsibility for failure to com-
ply with laws and standards governing the use of this equipment, in
particular; improper use, defective power supply, lack of maintenance,
instructions contained in this manual.
IMER INTERNATIONAL reserves the right to modify features of the saw
and contents of this manual, without the obligation to update previous
machines and/or manuals.
2.
Table 1 - TECHNICAL DATA
Model Combi 250/1000 VA
Max. blade diameter 250 mm
Diamond Blade hole
25.4 mm
diameter
Single phase motor power 1.5 kW
Max. blade rotation speed 2800 rpm
Cutting table dimensions 1115x500 mm
Length of 90° cuts
950 mm
(thickness= 10mm)
1000 mm
Length of cuts from above
Maximum cut depth with
single stroke 66 mm
Maximum cut depth with 105 mm
two stroke
13 l/min
Water tank capacity
Machine dimensions 1420x636x619
Packed machine
1454x669x654 mm
dimensions
Weight with packaging
IMER INTERNATIONAL S.p.A.
COMBI 250/1000 VA - COMBI 250/1500 VA
Combi 250/1500 VA
250 mm
25.4 mm
1.5 kW
2800 rpm
1615x500 mm
1450 mm
1500 mm
66 mm
105 mm
13 L/min
40 L 40 L
1920x636x619 mm
1954x669x654 mm
65 kg 80 kg
Feature
Power (kW)
Rated voltage (V)
Frequency (Hz)
-
Absorbed current (A)
Number of poles
rpm
Service type
Insulation category
Protection category
Capacitor (µF)
Combi 250/1000 VA saws have been designed and manufactured ac-
cording to the following standards: UNI EN 12418:2001; EN 12100-
1/2:2005; EN 60204-1:2006.
Table 3 shows the sound pressure level measured loadless at the ope-
rator's ear (L ) and of the vibrations transmitted during operation.
pA
Model
Combi 250/1000 VA -
250/1500 VA
The Combi 250/1000 VA is a saw comprising the following main sub-
groups:
equipped with horizontal and vertical movement facilities. The alumi-
The machine is supported by a special metallic frame. There is a
shockproof plastic tank between the machine and the frame. The water
immersion pump is mounted below the cutting surfaces on a special bra-
cket and supplies a water distributor inside the blade guard for cooling
the cutting blade during operation.
main ON-OFF switch on the operator side to facilitate saw activation
and shutdown.The raised position of the red OFF button on the handle is
designed to facilitate shutdown of the machine in the event of an emer-
gency. The motor capacitor is located in a protected position inside the
handle.
tion and to protect the user during cutting cycles.
delivered to the cutting blade. The version 250/1500 Va the movement
This saw has been designed for cutting the following materials: ceramic
tiles, masonry and stone in general with maximum dimensions com-
patible with the length, cutting depth and dimensions of the surfaces
Maximum weight of processable materials: 25 kg.
ragraph 4.2.
by the manufacturer for this saw model, contact IMER INTERNATIONAL
S.p.A.
10
Table 2
Motor Motor
(230V/50Hz) (220V/60Hz) (110V/50Hz)
1.5 1.5
230 220
50 60
9.4 9.4
2 2
2800 2800
S6 40% S6 40%
F F
IP55 IP55
40 (Ø 45x96) 40 (Ø 45x96) 90 (Ø 50x120)
Table 3
Type of motor L
pA
Electric 86 dB
GB
Motor
1.5
110
50
15.4
2
2800
S6 40%
F
IP55
A
eq
2.57 m/s 2
-
-