AEG PWI 4914 FA Instrucciones De Servicio página 63

PW_4914_Bed_Anl_A5_3.qxd
2. After several
seconds „WT
0.0 kg (0.0
lb./0:0 St:)"
will appear
on the display
(Fig. 5).
3. If the scale is not switched on you will see
"WT - - - - kg (- - - - lb., - - - - St:)" on the
LCD display.
4. Step on the scale with both feet. Distribute
your weight evenly and wait for the scale to
calculate your weight. Hold the display
vertically or horizontally over the infrared
lamp on the scale.
5. The reading on the display initially flashes
2x, then your exact weight will be shown.
When you step off the scale, the device
will switch off automatically after 20
seconds.
Programming your
personal data
Attention: Carry out the following opera-
tions one after the other and within a few
seconds or the device will automatically
interrupt the programming mode!
1. Push the MODE button to switch on the
display. Wait until "WT 0.0 kg (0.0 lb./0:0
St:)" appears on the display. Use the UNIT
button to select your preferred unit (kg, lb.
or St:).
2. Push the
MODE button
again. Then,
push the SET
button to
change to the
programming mode. 'SEt' appears in the
LCD display, then 'P 01' (storage location)
starts to flash, and the preset symbol for
'male' and the preset value for the height in
cm (in.) are shown (fig. 6).
3. Select a storage location using the P/
ATH/ buttons.
4. Then push the SET button and the display
changes to the next setting.
5. The symbol for 'male' flashes on the
display. Use the P/
28.08.2007 12:30 Uhr
6. Push the SET button again to change to
(fig. 5)
7. Push the SET button again to change to
8. Pushing the SET button again will cause
a. Push the MODE button three times to view
b. If you want to make any changes push the
(fig. 6)
c. If you wait for more than 15 seconds wit-
Your personal data is now stored in the
/ selected storage location.
There is an overall number of 16 storage
locations. The remaining 15 storage locati-
ons can be used to store also the personal
data of other members of your family or other
/ ATH/ buttons to users of these scales.
Seite 63
select a setting ('male' or 'female').
the HEIGHT setting. The indication '170'
(67.0) flashes. Use the P/
tons to select a value between 80 (31.5 in)
and 240 cm (94.5 in).
the AGE setting. The indication '30' flas-
hes. Push one of the buttons ATH/
P/ and hold it down to run up or down
through the values in fast mode. Use the
P/ / ATH/ buttons to select a value
between 6 and 100 years. If the age is set
to a value under 16 years, a child's face
will be shown in the display next to the
male/female symbol.
the storage location, sex, age and entered
height to be displayed for a few seconds,
then the indication changes to "WT 0.0 kg
(0.0 lb./0: 0
St:) and - - -
(HT)". If the
scale is not
switched on
the reading
will be as
shown in Fig. 7.
all settings again. The reading must be as
shown in Fig. 6.
MODE button until the display reads as
shown in Fig. 6. By pushing the P/
ton you change to the selection mode.
Now choose the storage location with the
settings you wish change (flashing indicati-
on) using the P/ and ATH/
push the SET button. Proceed as descri-
bed in steps 4 to 6.
hout changing anything the reading chan-
ges back to the time.
GB
/ ATH/ but-
or
(fig. 7)
but-
buttons and
63