User Options - DSC WTK5504 Manual Del Usuario Y Operador

Ocultar thumbs Ver también para WTK5504:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Indicators
Ready - lit when the system/partition is ready to be armed.
Armed - lit when the system/partition is armed.
Trouble - lit when there is a trouble on the system; flashes when battery is low.
AC Power - lit when power is present; off when power is absent.
System Chime (Chime Enable/Disable)
Home > More > Functions > System Chime
Press the key to choose the setting opposite to the one currently in use. A brief message of either "Door Chime
Enabled" or "Door Chime Disabled" will appear to indicate the current setting. When chime is enabled, you can use
the Voice Chime button on the Home screen to select Voice Chime, Chime, or No Chime.
Quick Exit
Home > More > Functions > Quick Exit
If the system is armed and you need to exit, use the quick exit function to avoid disarming and rearming the system. To
activate this function, press Quick Exit. The "Quick Exit in Progress" screen appears and the voice prompt says,
"Quick exit in progress" followed by "Please exit now". You have 2 minutes to leave the premises through your exit
door. When the door is closed again the remaining exit time is cancelled.
Outputs
Home > More > Functions > Outputs
Your installer may have programmed these keys to perform other functions (reset sensors after an alarm, open your
garage door etc.) To activate these functions, press the appropriate option. See also Sensor Reset on page 7.
Clean Mode
Home > More > Functions > Clean Mode
Clean Mode allows the user to touch (i.e., clean) the screen without enabling or disabling any functions. The screen
will remain in this mode for 30 seconds, then return to the More Functions screen.

User Options

Access Codes
Home > More > User Options > Access Code Prog [Master Code]
When Access Code Programming is selected from the User Options menu, the keypad prompts for a Master Code.
When a valid Master Code is entered, a numeric keypad is displayed with arrows to scroll to the desired user to add/
edit. Press the select button to enter the user options or enter the 2-digit user number to jump directly to a user.
Setting an Access Code
1.
Select "Set Access Code". A keypad screen is shown with the existing code. If there is no existing code,
"AAAA" (or AAAAAA for 6 digits) is shown.
2.
Start to enter a new code. The code area will be cleared, and the new code will be shown. If the clear key is
pressed, the new code will be cleared, but the old code is not deleted by this action. Once the last digit is
entered the new code will have replaced the old code; no further action is required to save the code. If the
screen "times out" (goes grey or black) or you exit the screen without completing the new code, the previous
code will remain.
Erasing an Access Code
To erase a code, select the code and choose Delete User. The system will delete the code immediately and the user will
be returned to select another code.
Proximity (Prox) Tag Enrollment and Use (WTK5504P keypad only)
Home > More > User Options > Access Code Prog [Master Code] > Select
User > User xx settings > Prox Tag Prog
Enrolling Proximity Tags
1.
Press Prox Tag Programming.
2.
Place the prox tag near the tag reader
"Tag Enrolled Successfully" will be displayed and the keypad will beep. If the proximity tag has been enrolled
previously, an error tone will sound. The screen will read "Duplicate Tag/User Code".
NOTE: Prox tags do not work on PowerSeries panels.
Erasing Prox Tags
Delete tags from the system when they are lost or no longer needed. To delete a proximity tag, the user code it is asso-
ciated with must be deleted.
1.
Press More > User Options > Access Code Prog. [Master Code].
2.
Use left and right arrow buttons to select the user number associated with the proximity tag to be deleted and
press Select.
3.
Press Delete User and confirm by pressing Yes.
5
at the top of the keypad to assign it to the user code. The message

Publicidad

Tabla de contenido
loading

Tabla de contenido