Positioning Refrigerant And Drain Piping - Mitsubishi Electric City Multi PKFY-P NAMU-E Serie Manual De Instalación E Usuario

4. Installing the refrigerant piping
I PKFY-P06/P08NAMU-E
1
A
26-31/32 ( 660 )
17-23/32 ( 450 )
20-25/32 ( 520 )
2 E F
2-1/8 ( 54 )
I
31/32 ( 24.4 )
J
H
K 5/8 ( 16 )
Fig. 4-3
I PKFY-P12/P15NGMU-E
1
E
1-3/8 ( 35 ) 22-7/8 ( 581 )
B
17-11/16 ( 449 )
C
A
27-9/16 ( 700 )
D
E F
2
H
13/32 ( 10 )
7/8 ( 22 )
5/16 ( 8 )
2-3/4
( 70 )
2-3/8
I
7-15/32 ( 190 )
( 60 )
Fig. 4-4
I PKFY-P18/P24/P30NFMU-E
1
E
43-11/16 ( 1110 )
B
31/32 ( 25 ) B
Fig. 4-5
2
F
1-3/16
( 30 )
1-9/16
( 39 )
1-15/32
( 37 )
2-29/32
( 74 )
Fig. 4-6
3
J
M
Fig. 4-7
10
B
C
4-11/32
D
( 110 )
C
4-9/16
B
( 116 )
G
I
L
K
13/32 ( 10 )
3/32 ( 2.5 )
1-11/32
( 34 )
1-25/32 3-19/32
( 45 ) ( 91.5 )
C
B
2-1/8 ( 54 )
3-3/8 ( 86 )
D
F
6-1/32 ( 153 )
G
I
H
H
5/16 ( 8 )
1-3/8 ( 35 )
2-3/8
I
( 60 )
C
D
2-5/32 ( 55 ) D
B
A
4-23/32 ( 120 )
4-3/8 ( 111 )
C
7-7/32 ( 183 )
G H
1-3/16 ( 30 )
3-27/32 1-1/4
( 98 ) ( 32 )
1-15/32
( 37 )
2-29/32
( 74 )
13-3/8 ( 340 )
L

4.3. Positioning refrigerant and drain piping

I PKFY-P06/P08NAMU-E (Fig. 4-3)
in.(mm)
1 Position of refrigerant and drain piping
• The drain pipe can be cut midway to meet the on-site conditions.
A (Total length of flexible hose)
B Liquid pipe
C Gas pipe
D Drain hose
2 Determine the position of the knockout holes on the unit body.
s Cut the knockout holes using a saw blade or an adequate knife.
Take care not to damage other parts of the unit.
• Remove the corner box and drill a knockout hole. If a hole is made without remov-
ing the box, the drain hose could be damaged.
E Left-side piping
F Lower piping
G Right-side piping
H Knockout hole for left-side piping
I Corner box
J Knockout hole for lower piping
K Through hole for the remote controller's cable
L Knockout hole for right-side piping
I PKFY-P12/P15NGMU-E (Fig. 4-4)
1 Position of refrigerant and drain piping
in.(mm)
• The drain pipe can be cut midway to meet the on-site conditions.
A (Total length of flexible hose)
B Liquid pipe
C Gas pipe
2 Determine the position of the knockout holes on the unit body.
s Cut the knockout holes using a saw blade or an adequate knife.
Take care not to damage other parts of the unit.
• Remove the corner box and drill a knockout hole. If a hole is made without remov-
ing the box, the drain hose could be damaged.
E Left-side piping
F Lower piping
G Right-side piping
I PKFY-P18/P24/P30NFMU-E
1 Position of refrigerant and drain piping (Fig. 4-5)
in.(mm)
Models
P18/P24NFMU-E
P30NFMU-E
B Drain hose
C Liquid pipe
D Gas pipe
E Drain hose in left-side piping
• The drain pipe can be cut midway to meet the on-site conditions.
2 Determine the position of the knockout holes on the unit body. (Fig. 4-6)
F For left-side piping
G For lower-side piping
H For right-side piping
• Make the knockout holes using a saw blade or an adequate knife.
Caution:
The side panel must be removed before drilling a knockout hole in it.
If a hole is made with the side panel in place, the refrigerant pipe within the unit
could be damaged.
3 L-shaped connection pipe (for gas piping) (Fig. 4-7)
K
J L-shaped connection pipe (optional parts)
K Unit side
L On-site piping side
M Piping (purchased locally)
J
Caution:
These items are used for right, lower or left side piping.
D Drain hose
E Left-side piping
F Right-side piping
H Remote controller cable through hole
I Corner box
A
4-7/32 (107)
4-1/32 (102)
in.(mm)