Emerson InSinkErator CWT-00 Manual Del Propietário página 5

Follow these steps for installing chilled water tank with a cold only faucet.
2
INSTALLING THE COLD ONLY FAUCET
a
Property Damage: Do not pinch or break copper
Brass Nut
tubing. Do not distort the last 1" of tubing.
b
Brass Nut
An assistant may be needed to hold
the faucet in place
while securing the base.
3
INSTALLING THE WATER TANK
a
Inlet
Property Damage: All tubes must be cut
Inlet
squarely with no burrs.
Outlet
b
Outlet
1
Property Damage: Do not pinch or break tubing.
Do not distort the last 1" of tubing.
Pull on connection to ensure fully engaged.
8
Unpack faucet components.
On a firm, flat surface, carefully
straighten the copper tubing.
Ensure that the black O-ring is
properly seated in the base of the
faucet (the groove on the underside
of the faucet base).
Brass Nut
Ferrule
Brass Insert Ferrule
1
4
Plastic
Feed tube down through sink hole
tube
until the base is at rest.
From under the sink, place the
Brass Nut
Ferrule
semi-circular mounting plate onto
Ferrule
Brass Insert
the threaded stud.
1
4
Plastic Place hex nut onto the threaded stud.
tube
Ensure faucet is at desired angle.
Insert screwdriver into hole on side of
hex tool (creating a "T"), and use tool
to tighten nut and secure faucet.
Attach supplied quick connect elbow
to end of supplied white 1/4" tube.
Attach quick connect elbow to water
Inlet on front of chilled water tank.
Measure distance from water inlet
on chilled water tank to water
supply valve. Carefully trim white
1/4" tube, allowing ample slack
in tubing.
Attach supplied quick connect elbow
to end of supplied blue 1/4" tube.
Attach quick connect elbow with
blue tube to water Outlet on front of
chilled water tank.
2 White Tape
Measure distance from chilled water
tank outlet to water supply line on
faucet. Carefully trim blue tube to
correct length.
Using quick connect elbow, connect
blue tube to faucet water supply.
3
Follow these steps for installing chilled water tank with a cold only faucet.
4
WATER CONNECTION
a
Brass Nut
Brass Nut
Brass Nut
Ferrule
Brass Insert
1
4
Plastic
tube
Property Damage: Join remaining tube to
cold water supply only. Water supply valves
must not prevent backward flow.
a
Brass Nut
Brass Nut
Ferrule Brass Nut
Brass Insert
1
4
Plastic
tube
Inlet
Property Damage: Join remaining tube to
cold water supply only. Water supply valves
must not prevent backwards flow.
Inlet
5
FILL TANK & CONNECT POWER
Brass Nut
a
Ferrule Outlet
Brass Insert
Plastic
tube
Outlet
Property Damage: Before plugging in
chilled water tank, check for leaks in all
Inlet
water supply connections.
b
Inlet
Outlet
Electric Shock Hazard: A standard grounded
outlet is required under the sink. Do not use an
extension cord set with the chilled water tank.
Outlet
With no filtration system:
Brass Nut
Install a T-fitting (not included)
Ferrule
Ferrule
Ferrule
Brass Insert
onto the cold water supply line.
Install dedicated water control valve with
1
4
Plastic
1/4" compression fitting (not included).
tube
Place 1/4" brass insert (included)
into end of white tube.
Attach remaining end of the supplied
white 1/4" tube into the 1/4"
compression fitting and tighten.
With optional InSinkErator filtration system:
For filtration installation instructions,
see installation guide packed with the
Brass Nut
Ferrule system.
Ferrule
Brass Insert Ferrule
Install a T-fitting (not included)
onto the cold water supply line.
1
4
Plastic
Install dedicated water control
tube
valve with 3/8" compression fitting
(not included).
Install brass nut, ferrule and tube
insert at the end of the white3/8"
tube from filter.
Insert the white 3/8" tube into the
3/8" compression fitting and tighten.
Brass Nut
Ferrule
Turn on the cold water supply.
Depress the faucet handle and hold it
until water flows from the spout.
Allow water to run for at least 60
seconds after water begins to flow
from faucet.
Check all connections to ensure they
are tight and that there are no leaks.
Plug in chilled water tank.
Prior to drinking water from the
chilled water tank, run the water for
at least 5 minutes to flush lines.
water to reach target temperature.
Allow up to 60 minutes for
9