System Requirements - Facom SCANDIAG DX.TSCANPB Manual De Instrucciones

1. Connect the power cable's USB connector
connector 2 on the Brake Disc and Tyre Analyzer.
2. Connect the power cable's USB connector to the charger
3. Connect the charger to a power socket.
Unit Off Charge Time
Unit On Charge Time
Multifunction Button (Fig. A)
The Brake Disc and Tyre Analyzer is switched on and off by
pressing the power button with built-in multi-colour LED
The multifunction button activates the laser beam and the
micro-camera while the tests are in progress.
- to power on the Brake Disc and tyre Analyzer, press
the multifunction button with built-in multi-colour
LED for 1 second.
1
- to power off the Brake Disc and tyre Analyzer,
press the multifunction button with built-in multi-colour
LED 1 for 5 seconds.
- to record a measurement, click the multifunction
button with built-in multi-colour LED.
Multi-Colour LED Blink Codes
Colour Blink Status
Blue Slow blink No Bluetooth® connection
Continuously ON Tool connected via Bluetooth®
Green Slow blink Battery charge < 95%
Continuously ON Battery charge ≥ 95%
Red Slow blink Low battery
Automatic Shutdown
If there is no power via USB, the Brake Disc and Tyre Analyzer
switches off automatically after 5 minutes of inactivity.
Adapter (Fig. A–C)

WARNING: Risk of damage. Do not try to remove the
adapter by pressing on the front part of it.

WARNING: Remove the adapter if analysing the
disc's state of wear to avoid distorting the micro-
camera's readings.
The Brake Disc and Tyre Analyzer is equipped with a magnetic
adapter designed to be used only for the analysis of the tyre's
state of wear.
Connect Adapter
Place the magnet 5 into the specific housing on the tyre wear
analysis adapter 6 or the measurement system check
adapter 7 .
Disconnect Adapter
Lightly press the rear part of the tyre wear analysis adapter
or the measurement system check adapter
to the USB
8
1.5 Hrs
4 Hrs
1 .
Notes
--
Tool charging
and ON
Tool charging
and ON
6
7 to disconnect it
from the magnet. Do not remove the tyre wear analysis adapter
or the measurement system check adapter by pressing on the
front of it.
9 .
SCANDIAG SOFTWARE SETUP

System Requirements

Below you will find a list of system requirements for installing
the SCANDIAG software on a PC. SCANDIAG software is
compatible with the following Microsoft operating systems:
• Windows 7 - Service Pack 1 - x86 / x64
• Windows 8 / 8.1 - x86 / x64
• Windows 10 - Version 1607, Build 14393 recommended -
x86 / x64
Operating systems Windows RT and Windows 10 S are
not supported.
Requirement
Space on hard disk *
RAM
Screen resolution
DVD player
1 USB 2.0 port (type A
Internet Connection **
Bluetooth®
(*) The request for space on the hard disk refers to a single
diagnostic environment for its first installation.
The recommended space takes into account the possibility to
update the software to higher versions.
(**) The Internet connection is necessary in order to access the
on-line services, perform updates, etc.
In order to optimise the use and reduce the risk of possible
compatibility problems, we recommend that this software be
installed on a PC that is dedicated exclusively to workshop use
Bluetooth® Resources
The SCANDIAG software provides special automatic
configuration functions for products equipped with
Bluetooth® technology.
To use these functions, you must install the software on a PC
equipped with Bluetooth® peripheral devices.
The software supports the following drivers:
• Microsoft™
• WIDCOMM™ 1.4.2 Build 10 or higher
• TOSHIBA™ 4 or higher
If the drivers used are not supported by the software, you will
not be able to use the automatic configuration procedures.
As an alternative, use the Bluetooth® manual configuration
functions provided by your operating system.
We do not recommend installing Bluetooth® peripheral devices
(USB flash drives) on PCs with a built-in Bluetooth® system.
eNGLIsh
Minimum
1 GB
2 GB
1280x720 pixel
No
Yes
Yes
Yes
19