Code Retrieval - RCA RCR311B Manual Del Usuario

Ocultar thumbs Ver también para RCR311B:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

RCR311B_NA_IB_REVB_K4.qxd 7/27/04
Programming Methods (continued)
a. Press and hold the VCR•DVD
ON•OFF
VCR
DVD
b. While holding down the
(BLINK)
VCR
DVD
c. Release the VCR•DVD key.
VCR
DVD
ON•OFF
(BLINK)
4. Press and hold the component key
VCR
DVD
(TV, VCR•DVD, SAT•CBL) you
TV
SAT
CBL
wish to program. The illuminated
ON•OFF key turns on and
ON•OFF
remains on.
5. While holding the component key
down, press and hold the ON•OFF
key. The illuminated ON•OFF key
(BLINK)
turns off.
6. After holding down both keys for
ON
OFF
three seconds, the illuminated
ON•OFF key turns back on.
7. Release both keys. The illuminated
ON•OFF key remains on.
!
TIP:
of each key, be sure to keep the remote
pointed at the IR sensor of the
component you are currently
programming the remote to control.
8. Press and release the PLAY key,
PLAY
then wait five seconds to see if
your component turns off. If your
component does not respond,
ON•OFF
continue to press the PLAY key
every five seconds until your
component turns off. Each time
you press the PLAY key, the
(BLINK)
illuminated ON•OFF key blinks
and a block of 10 codes are sent to
your component. This process
continues until all of the codes in
the Code Lists have been searched.
(If your component has not turned
off after all codes have been
searched, the illuminated ON•OFF
key blinks four times and turns
off. The Auto Code Search Entry
method is exited.)
9. When your component turns off,
you know the correct code is in
the last block of 10 codes sent.
Press and release the REVERSE
key. Wait two seconds to see if
REVERSE
ON•OFF
your component turns on again. If
your component does not respond,
continue to press the REVERSE
key every two seconds until your
component turns on again. This
(BLINK)
will isolate the correct code in the
last block of codes sent. Each time
10
11:46 AM
Page 10
key. The illuminated ON•OFF
key turns on.
VCR•DVD key, press and
release the number 2 key on
the keypad to control a VCR or
the number 3 key to control a
DVD. The illuminated
ON•OFF key turns off.
The illuminated ON•OFF key
blinks four times and then
turns off. Your remote is now
either in VCR or DVD
Programming Mode,
depending on which you
chose. Proceed to step 4.
Throughout the programming
the REVERSE key is pressed, the
illuminated ON•OFF key blinks.
Note:
the REVERSE key after your
component responds, press and
release the FORWARD key. Then,
FORWARD
wait two seconds to see if your
component turns off again.
10. Once your component turns off,
you have found the correct code.
STOP
You must save the new code by
pressing and releasing the STOP
key. The illuminated ON•OFF key
ON
OFF
turns off. You must press the
STOP key to save the code or the
correct code will not be stored!
11. To confirm that the component
key is programmed with the
correct code for maximum
functionality, test the component.
Attempt to control a variety of the
component's functions with the
remote. If some of the features of
your components do not work,
different codes in the list can be
tried until you find the code that
allows the remote to control the
majority of your component's
functions. See the section entitled
"Testing the Code for Maximum
Functionality" on page 8 for
more information.

Code Retrieval

Once you've programmed the remote to control your
components, you may want to record the codes for future
reference. If you used the Direct Code Entry method, this is
easy. Just find the codes you programmed in and make a note
of them in the boxes on the next page. If you used one of the
Code Search methods to program your remote, you will need
to retrieve each component's four-digit code. Retrieving the
actual code and writing it down will save you time if you
ever need to program the remote again (e.g., if programming is
lost when you change the batteries). If the codes are recorded,
you can use the Direct Entry method to reprogram your
remote to control your components, which is quick and easy.
1. Press and hold the component key
VCR
DVD
(TV, VCR•DVD, SAT•CBL) whose
TV
SAT
CBL
code you wish to retrieve. The
ON•OFF
illuminated ON•OFF key turns on.
2. While holding the component key
INFO
down, press and hold the INFO
key. The illuminated ON•OFF key
turns off.
ON•OFF
3. After holding down both keys for
three seconds, the illuminated
ON•OFF key turns back on.
4. Release both keys. The illuminated
ON•OFF key remains on.
If you accidentally press
11

Publicidad

Tabla de contenido
loading

Tabla de contenido