Functional Description; Overload Protection - Makita DLM382 Manual De Instrucciones

Installing the handle
NOTICE:
When installing handles, position the
cords so that they are not caught by anything
between the handles. If the cord is damaged, the
mower switch may not work.
1. Slide the both ends of lower handle into the
grooves of the mower then fully tighten the clamping
screws.
► Fig.4: 1. Clamping screw 2. Lower handle
2. Align the screw holes of upper handle and lower
handle. Secure them with the clamping screws and
nuts.
► Fig.5: 1. Clamping nut 2. Clamping screw
NOTE: Hold the upper handle firmly so that it does
not drop off your hand.
3. Attach the holders to the handle. Position the
power supply cord as shown in the figure.
► Fig.6: 1. Holder
Removing the mulching plug
Optional accessory
1. Open the rear cover.
► Fig.7: 1. Rear cover
2.
Hold the mulching plug by the handle, and then
pull it out from the mower body as shown in the figure.
► Fig.8: 1. Mulching plug 2. Handle
Installing the grass basket
1.
Open the rear cover.
► Fig.9: 1. Rear cover
2. Hook the grass basket on the rod of the mower
body as shown in the figure.
► Fig.10: 1. Hook 2. Rod 3. Grass basket
Attaching the mulching plug
Optional accessory
1. Open the rear cover, and then remove the grass
basket.
► Fig.11: 1. Rear cover 2. Grass basket
2. Hold the mulching plug by the handle, and then
attach it to the mower body as shown in the figure.
► Fig.12: 1. Mulching plug 2. Handle

FUNCTIONAL DESCRIPTION

Installing or removing battery cartridge
CAUTION:
Always switch off the machine
before installing or removing of the battery
cartridge.
CAUTION:
Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the machine, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: The machine does not work with only one
battery cartridge.
To install the battery cartridge;
1. Slide the battery cover locking lever and open the
battery cover.
► Fig.13: 1. Battery cover 2. Battery cover locking
lever
2.
Align the tongue on the battery cartridge with the
slot on the mower then slide the cartridge until it locks in
place with a little click.
► Fig.14: 1. Battery cartridge
3. Insert the lock key in the place shown in the figure
as far as it will go.
► Fig.15: 1. Lock key
4.
Close the battery cover and push it until it is
latched with the locking lever.
To remove the battery cartridge from the mower;
1. Slide the battery cover locking lever and open the
battery cover.
2. Pull out the battery cartridge from the mower while
sliding the button on the front of the cartridge.
3.
Pull out the lock key.
4. Close the battery cover.
Machine / battery protection system
The machine is equipped with a machine/battery
protection system. This system automatically cuts off
power to the motor to extend tool and battery life. The
machine will automatically stop during operation if the
machine or battery is placed under one of the following
conditions.

Overload protection

When the machine is operated in a manner that causes
it to draw an abnormally high current, the machine
automatically stops without any indication. In this situ-
ation, turn the machine off and stop the application that
caused the machine to become overloaded. Then turn
the machine on to restart.
12 ENGLISH