Dimplex DF2550-EU-E Manual De Uso página 6

Remote Control - See Fig. 2
The maximum range of use is ~ 5metres.
NOTE: It takes time for the receiver to respond to the
transmitter.
NOTE: The reciever for the remote control is located in
the display, aim the remote control in this direction when
inputting commands.
Do not press the buttons more than once within two
seconds for correct operation.
Battery Information - See Fig. 2
1. To activate the remote control remove the clear battery
isolation strip at the base of the remote control, which
is used to ensure your remote control reaches you fully
charged.
2. To replace the remote control battery, turn over the
remote control, and follow the diagram embossed on the
remote control
3. Only use CR2025 or CR2032 size of batteries.
Fitting - See Fig. 3, 4 & 5
NOTE: If not using a Dimplex mantel, the fireplace must
be installed in an enclosure with the following minimum
internal/opening dimensions (Fig. 4).
New Wall Construction
① Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and high
traffic.
② Place the fireplace in the desired location to see how
it will look in the room.
③ Mark the desired location on the floor and store the
fireplace in a safe, dry and dust free location.
④ Use studs to frame an opening of 626 mm wide x 464
mm high x 225 mm deep.
Option #1 - The power cord can be lead from behind the
trim and along the wall to an outlet near the fireplace.
Option #2 - A new outlet can be installed inside the new
frame construction. Plug the unit into a 13 Amp, 230-240
Volt outlet. If the cord does not reach, you may use a
3-core type extension cord rated for a minimum of 13
Amps.
CAUTION: Clearance for air circulation beneath the
fireplace insert is provided by two (2) rubber feet.
Do not install the fireplace insert directly on carpet or
similar surfaces which may restrict air circulation.
If installing the fireplace in a carpeted area, place a one-
piece, solid, flat surface under the fireplace insert. Ensure
that both of the insert's feet rest securely on this surface.
Final Steps
Once complete the product is in the desired location ,
hang the front glass assembly on the mounts of the firebox
as shown in Fig. 4.
Use the supplied two (2) Phillips sheet metal screws to fasten
the glass assembly tabs to the fireplace (Figure 5).
Thermal Safety Cut-out
The built-in overheat cut-out, switches off the appliance
automatically in the event of a fault! Should this occur
switch off the appliance or disconnect the mains plug
from the socket.
Remove any obstructions which may have caused the
overheating. After a short cooling down phase, the
appliance is ready for use again! If the fault should occur
again, contact your local dealer!
WARNING: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched
on and off by the utility.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) lamps. These
LED lamps are maintenance-free and should not require
replacing during the life of the product.
Cleaning
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use
abrasive cleaners. The glass viewing screen should be
cleaned carefully with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush
attachment of a vacuum cleaner should occasionally be
used to clean the outlet grille of the fan heater.
WARNING: do not operate the product without the grille
and outer glass in position as this may effect the operation
of the heater.
Recycling
For electrical products sold within the
European Community. At the end of the
electrical products useful life it should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice in your country.
After Sales Service
Should you require after sales service or should you need
to purchase any spares, please contact the retailer from
whom the appliance was purchased or contact the
service number relevant to your country on the warranty
card.
Please do not return a faulty product to us in the first
instance as this may result in loss or damage and delay
in providing you with a satisfactory service. Please retain
your receipt as proof of purchase.